Question is ⇒ The power dissipation in a transistor is the product of, Options are ⇒ (A) emitter current and emitter to base voltage, (B) emitter current and collector to emitter voltage, (C) collector current and collector to emitter voltage, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ The power dissipation in a transistor is the product of, Options are ⇒ (A) emitter current and emitter to base voltage, (B) emitter current and collector to emitter voltage, (C) collector current and collector to emitter voltage, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The power dissipation in a transistor is the product of
A.	emitter current and emitter to base voltage [Wrong Answer]
B.	emitter current and collector to emitter voltage [Wrong Answer]
C.	collector current and collector to emitter voltage [Correct Answer]
D.	none of the above [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ An RF carrier of 12 kV at 1 MHz is amplitude modulated by 1 kHz signal having peak value of 6 kV. The modulation pattern is seen on CRO screen. The voltage indicated will be
18 kV
1.001 kV
6 kV
36 kV

⇒ An end fire array consisting of several half-wave lengths of directive gain 40, then find the width of major lobe
60
50
51.25
None of the above

⇒

Match the following:

	List I		List II
A.	Zener diode	1.	used in seven segment display
B.	Tunnel diode	2.	used in voltage regulator circuits
C.	LED	3.	used is solar energy utilization
D.	Photovoltaic cell	4.	used in digital circuits

A-1, B-3, C-2, D-4
A-2, B-3, C-1, D-4
A-2, B-4, C-1, D-3
A-3, B-2, C-4, D-1

⇒ Time rate of change in heat energy is analogous to
voltage
charge
current
voltage gradient

⇒ For a half wave rectified voltage, the form factor and peak factor respectively are
1.11 and 2
1.57 and 2
1.11 and 1.11
1.57 and 2

⇒ Consider the following types of distortions in diode detectors

Distortion is caused due to the reason that dc and ac load impedances are unequal
Distortion is caused because ac load impedance has a reactive component at high audio frequencies
Audio frequency diode current is less than dc current

Which of the above are true?
1, 2 and 3
1 and 2
1 and 3
2 and 3

⇒ In pulse transmitter the ratio of time on to time off is called
efficiency
duty cycle
base
bandwidth

⇒ It is desired to route data from many registers to one register. The device needed is
decoder
multiplexer
demultiplexer
counter

⇒ Discharge breakdown in insulators is due to voids.
TRUE
FALSE

⇒ - 56 is not a valid real constant in Fortran.
TRUE
FALSE

⇒ Ultra high frequency oscillators work in the range
20 Hz to 20 kHz
1 kHz to 30 kHz
30 kHz to 30 MHz
above 30 MHz

⇒ In the op-amp circuit of figure, V_{0V_i
3 V_i
5 V_i
0.5 V_i}

⇒ The turn off time of a bipolar transistor is about
0.5 ns
10 ns
70 ns
150 ns

⇒ The message carrying efficiency is best in
AM
FM
AM-SC
Phase modulation

⇒ Negative feedback reduces noise originating at the amplifier input.
TRUE
FALSE

⇒ A line is excited by a 100 V dc source. If reflection coefficients at both ends are 1 each then
there will be no oscillations on line
there will be only 1 or 2 oscillations on line
there will be a finite number of oscillations on line
the oscillations will continue indefinitely

⇒

Assertion (A): A quarter wave transformer is used to match a resistive load to a transmission line.

Reason (R): A quarter wave transformer is a transmission line of quarter wave length.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Which of the following pairs are correctly matched?

Brune's realisation : realisation with ideal transformer.
Cauer realisation : ladder realisation.
Bott Duffin realisation : with non ideal transformer.

Select the answer using the following codes:
1, 2 and 3
2 and 3
1 and 3
1 and 2

⇒ In a pulsed RADAR typical value of pulse duration and pulse frequency respectively are
1 μs and 50 Hz
1 μs and 500 Hz
4 μs and 50 Hz
4 μs and 500 Hz

⇒ The total bandwidth needed for an AM signal at 55.25 MHz with 0.5 MHz video modulation is
0.25 MHz
0.5 MHz
1 MHz
10 MHz

⇒ MS Excel is an application software for financial planning.
TRUE
FALSE

⇒ The programming language in which Excel records the macro code is
basic
visual basic
video basic
basic 2

⇒ A transmission line of characteristic impedance z₀ = 50 Ω. Phase Velocity = 2 x 10⁸ m/sec, and length l = 1 m is terminated by a load z₁ = (30 - j 40) ohms. The input impedance of the line for a frequency of 100 MHz will be
(30 + j x 40) Ω
(30 - j 40) Ω
(50 + j x 40) Ω
(50 - j 40) Ω

⇒

Assertion (A): In C a variable name can have upto 8 characters and special symbols can also be part of variable name.

Reason (R): In C a type declaration at the beginning of program indicates the type of variable name used in the program.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ All inverters use forced commutation.
TRUE
FALSE

⇒ In van der walls crystals, there exists a high degree of stability of the outer electron shell.
TRUE
FALSE

⇒ To obtain very high input and O/P impedance in a feedback amplifier, the type of feedback utilized
voltage series
current series
voltage shunt
current shunt

⇒

Match the following:

	List I		List II
A.	Darlington amplifier	1.	A circuit using pnp and npn transistors
B.	CB amplifier	2.	A CS amplifier driving a CG amplifier
C.	Cascade amplifier	3.	A circuit with over-all voltage gain close to 1 and very large input impedance
D.	Complementary symmetry amplifier	4.	A circuit with low input impedance

A-1, B-2, C-3, D-4
A-2, B-1, C-3, D-4
A-3, B-4, C-2, D-1
A-4, B-3, C-2, D-1

⇒ If the switch is thrown to the START position, Q and Y will be equal to
Q = 0, Y = 0
Q= 1, Y= 1
Q = 1, Y = CLK
Q = 0, Y = CLK

⇒ In a bipolar transistor
recombination in base regions of both n-p-n and p-n-p transistor is low
recombination in base regions of both n-p-n and p-n-p transistors is high
recombination in base region of n-p-n transistor is low but that in p-n-p transistor is high
recombination in base region of p-n-p transistor is low but that in n-p-n transistor is high