Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The point of contraflexure is a point where? |

A. | shear force changes sign [Wrong Answer] |

B. | bending moment changes sign [Correct Answer] |

C. | shear force is maximum [Wrong Answer] |

D. | bending moment is maximum [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The value of equivalent length is taken to be half of the actual length of a column with one end fixed and the other end free.

Agree

Disagree

Both (a) and (b)

None of these

⇒ The stress at which the extension of the material takes place more quickly as compared to the increase in load, is called.

elastic limit

yield point

ultimate point

breaking point

⇒ The maximum tangential stress in a thick cylindrical shell is always __________ the internal pressure acting on the shell.

equal to

less than

greater than

high than

⇒ The ratio of direct stress to volumetric strain in case of a body subjected to three mutually perpendicular stresses of equal intensity, is equal to

Young's modulus

bulk modulus

modulus of rigidity

modulus of elasticity

⇒ A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear stress of 200 MPa. The maximum shear stress will be

-100 MPa

250 MPa

300 MPa

400 MPa

⇒ If the rivets in adjacent rows are staggered and the outermost row has only one rivet, the arrangement of the rivets is called

chain riveting

zig zag riveting

diamond riveting

cross-cross riveting

⇒ Proof resilience per material is known as

resilience

proof resilience

modulus of resilience

toughness

⇒ In a thick cylindrical shell subjected to an internal pressure (

*p*), the maximum radial stress at the inner surface of the shell is.

zero

p (tensile)

-p (compressive)

2p (tensile)

⇒ The radius of the Mohr s circle in the given figure is equal to

sum of two principal stresses

sum of two principal stresses

half the sum of two principal stresses

half the difference of two principal stresses

⇒ Hooke's law holds good upto

yield point

limit of proportionality

breaking point

elastic limit

⇒ The energy absorbed in a body, when it is strained within the elastic limits, is known as

strain energy

resilience

proof resilience

modulus of resilience

⇒ A beam supported on more than two supports is called

simply supported beam

fixed beam

overhanging beam

continuous beam

⇒ The section modulus (

*Z*) of a beam is given by

I/y

I.y

y/I

M/I

⇒ A beam extending beyond the supports is called.

simply supported beam

fixed beam

overhanging beam

cantilever beam

⇒ The slenderness ratio is the ratio of.

area of column to least radius of gyration

length of column to least radius of gyration

least radius of gyration to area of column

least radius of gyration to length of column

⇒ A pressure vessel is said to be a thick shell, when.

it is made of thick sheets

the internal pressure is very high

the ratio of wall thickness of the vessel to its diameter is less than 1/10.

the ratio of wall thickness of the vessel to its diameter is greater than 1/10.

⇒ A riveted joint in which every rivet of a row is opposite to other rivet of the outer row, is known as

chain riveted joint

diamond riveted joint

cross-cross riveted joint

zig-zag riveted joint

⇒ Within elastic limit, shear stress is __________ shear strain.

equal to

less than

directly proportional to

inversely proportional to

⇒ A shaft revolving at ω rad / s transmits torque (

*T*) in N-m. The power developed is.

T.Ï‰ watts

2 Ï€ TÏ‰ watts

2Ï€ TÏ‰/75 watts

watts

⇒ When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under.

tensile stress

compressive stress

shear stress

bending stress

⇒ In a tensile test on mild steel specimen, the breaking stress as compared to ultimate tensile stress is

more

less

same

more/less depending on composition

⇒ A beam of uniform strength has?

same cross-section throughout the beam

same bending stress at every section

same bending moment at every section

same shear stress at every section

⇒ The maximum deflection of a fixed beam of length

*l*carrying a central point load

*W*is.

Wl/48 EI

WI3/96 EI

WI3/192 EI

WI3/384 EI

⇒ A shaft of diameter

*D*is subjected to a twisting moment (

*T*) and a bending moment (

*M*). If the maximum bending stress is equal to maximum shear stress developed, then

*M*is equal to.

T/2

T

2T

4T

⇒ When a rectangular beam is loaded longitudinally, the shear force develops on the top layer.

Agree

Disagree

True

False

⇒ The capacity of a strained body for doing work on the removal of the straining force, is called

strain energy

resilience

proof resilience

impact energy

⇒ For steel, the ultimate strength in shear as compared to in tension is nearly

same

half

one-third

two-third

⇒ In a simple bending of beams, the stress in the beam varies?

linearly

parabolically

hyperbolically

elliptically

⇒ In a beam subjected to pure bending, the intensity of stress in any fibre is __________ the distance of the fibre from the neutral axis.

equal to

less than

more than

directly proportional to

⇒ The load at which the column just buckles, is known as

buckling load

critical load

crippling load

any one of these