Question is ⇒ The pipes used in diesel engines from pump to nozzle is made up of, Options are ⇒ (A) PVC, (B) Rubber, (C) Steel, (D) Copper, (E) , Leave your comments or Download question paper.

Question is ⇒ The pipes used in diesel engines from pump to nozzle is made up of, Options are ⇒ (A) PVC, (B) Rubber, (C) Steel, (D) Copper, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The pipes used in diesel engines from pump to nozzle is made up of
A.	PVC [Wrong Answer]
B.	Rubber [Wrong Answer]
C.	Steel [Correct Answer]
D.	Copper [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ To equalize tyre wear, it is suggested that tyres be rotated from one wheel to another every
80 kms
8000 kms
800 kms

⇒ Propeller shaft includes
Universal joint
Knee joint
Slip joint

⇒ If the differential noise is present only when the car is rounding a curve the trouble would be due to
Heavy heel contact on gear teeth
Heavy toe contact on gear teeth
Binding in differential case

⇒ The fluid coupling has maximum efficiency when driving and driven members are turning at
High speed
Low speed
Different speed
About the same speed

⇒ The metering rod is designed to vary the size of which jets
High speed jets
Accelerating jets
Float level jets
Idle jets

⇒ Leaf spring for vehicles are nipped to
To vary the effective length of the spring
To increase the interleaf friction
Improve the load carrying capacity of spring
Ensure that all leaves are uniformly stressed during loading

⇒ The distance between adjacent meshing teeth of mating gears is called
Clearance
Back lash
Flank

⇒ The radius of a pneumatic tyre is
The radius of unloaded fully inflated tyre
The height of centre of tyre from the ground when it is loaded
Imaginary radius found by measuring the distance per revolution of the loaded tyre
It is fixed radius, based on the dimensions of the tyre

⇒ The release levers in a typical clutch pivot on
Springs
Levers
Threaded levers
Pins

⇒ The brake shoes are curved to conform to the inner diameter of the
Tyre
Wheel
Pedal
Brake drum

⇒ De Dion axle is usually
Used at the front of heavy vehicles
A kind of axle in which the differential and final drive gears are supported in the frame
A two speed axle drive suited for heavy vehicles
The popular drive for 2 wheeler

⇒ Immediately after ignition, combustion chamber temperatures may reach a value of
15000C
55000C
25000C
75000C

⇒ The material used for the piston of modern passenger cars are
Brass pistons
Cast iron pistons
Aluminiun alloy pistons
Steel pistons

⇒ Movement of the brake pedal forces brake fluid from the master brake cylinder through brake lines and into the
Brake shoes
Wheel cylinders
Brakes cables
Pedal rod

⇒ Brake lining area required for shoe brakes for trucks is mainly based on
Average truck speed
Frequency of brake applications
Gross vehicle weight
Material used for brake drums

⇒ In the Hotchkiss drive, the rear end torque is absorbed by the
Torque tube
Rear springs
Radius rods

⇒ The weight or pressure required to deflect a spring in mm is called the spring
Weight
Deflection
Rate
Rebound

⇒ During combustion the pressure in the cylinder may increase to as much as
50 Kg/cm2
400 Kg/cm2
10 Kg/cm2

⇒ In normal operation the part of the exhaust valve that gets the hottest is
Face
Middle of Stem
Centre of head
Edge of margin

⇒ As the battery is discharged, the active materials in both negative and positive plates are changed to
Spongy lead
Sulphuric acid
Lead oxide
Lead sulphate

⇒ When air is heated, it
Contracts and becomes heavier
Expands and becomes heavier
Expands and becomes lighter

⇒ In the high gear in the transmission, main shaft turns at the same speed as the
Idler shaft
Counter shaft
Clutch shaft

⇒ The sun gear in the planetary gear system meshes with the
Pinion cage
Ring gear
Clutch gear
Planet pinions

⇒ Engine torque is highest at
Low speed
Intermediate speed
High speed

⇒ As the number of cylinders in multi cylinder engines increases the power to weight ratio .........
Remains the same
Increases
Becomes zero
Decreases

⇒ The heat is added in the cycle at
Constant pressure
Constant volume
Approximately constant pressure and constant volume

⇒ When petrol burns completely, two of the compounds that are formed are
Carbon dioxide and water
Water and oxygen
Hydrocarbon and oxygen

⇒ The rear end suspension arrangement in which rear end torque is absorbed by the spring is called the
Torque tube drive
Hooks drive
Differential drive
Hotchkiss drive

⇒ In the multiplier power brake system, movement of the brake pedal
Increases the hydraulic pressure which actuates the control valve
Actuates the valve in the bellows through linkage
Actuates the valve to admit atmospheric pressure to one side of the diaphragm

⇒ A negative loop in the P.V diagram of an I.C engine is due to
Pre ignition in the engine
Suction of air for engine
Pre opening of the exhaust valve
High pressure in the cylinder