Question is ⇒ The output voltage of 5-bit D/A binary ladder that has a digital input of 11010 (Assuming 0 = 0 V and 1 = + 10 V) is, Options are ⇒ (A) 3.4375 V, (B) 6.0 V, (C) 8.125 V, (D) 8.6875 V, (E) , Leave your comments or Download question paper.

Question is ⇒ The output voltage of 5-bit D/A binary ladder that has a digital input of 11010 (Assuming 0 = 0 V and 1 = + 10 V) is, Options are ⇒ (A) 3.4375 V, (B) 6.0 V, (C) 8.125 V, (D) 8.6875 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The output voltage of 5-bit D/A binary ladder that has a digital input of 11010 (Assuming 0 = 0 V and 1 = + 10 V) is
A.	3.4375 V [Wrong Answer]
B.	6.0 V [Wrong Answer]
C.	8.125 V [Correct Answer]
D.	8.6875 V [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A triangular Pulse of 10 V peak is applied to a capacitor of 0.4 F. The change of the capacitor and its wavefor
8 rectangular
8 triangular
4 triangular
4 rectangular

⇒ A transistor with a = 0.9 and I_CBO = 10 μA is biased so that I_BQ = 90 μA. Then I_CQ will be
910 mA
5 mA
5.25 mA
4.95 mA

⇒ The capacitance of a capacitor is not affected by
area of plates
thickness of plates
∈_r
distance between plates

⇒ Which of the following devices has substrate?
JFET
Depletion Type MOSFET
Enhancement type MOSFET
Both (b) and (c)

⇒ In rectifier circuits, ripple factor RF and form factor FF are related as
RF = (FF² - 1)^0.5
RF = FF
RF = FF - 1
RF = (FF - 1)^0.5

⇒ A full wave rectifier circuit using centre tapped transformer and a bridge rectifier are fed at 100 V, 50 Hz. The frequencies of outputs in these two rectifiers are
100 Hz each
50 Hz each
100 Hz and 50 Hz
50 Hz and 100 Hz

⇒ An op-amp has zero gain for common mode inputs. Then CMRR =
zero
infinite
high
low

⇒ The electric flux and field intensity inside a conducting sphere is
minimum
maximum
uniform
zero

⇒ An instruction using immediate addressing mode in 8085 is
2 bytes long
3 bytes long
2 or 3 bytes long
1 or 2 or 3 bytes long

⇒ A typical signal strength received from a geosynchronous communication satellite is of the order of a few
milliwatts
kilowatts
picowatts
watts

⇒ In figure, the switch is initially open. At t = 0 switch is closed. v_c (0⁺) and i_L (0⁺)
60 V and - 0.3 A
150 V and zero
zero and 0.3 A
90 V and - 0.3 A

⇒ Symbol shown in figure represen
Enhancement only N-channel MOSFET
UJT with p-type base
N-channel DMOSFET with internal protection
Phototransistor

⇒ In a circuit containing a complex impedance, maximum power transfer takes place when load is
pure resistance
equal to the complex impedance
conjugate complex of the circuit impedance
none of the above

⇒ A Yagi antenna has a driven antenna
only
with a reflector
with one or more directors
with a reflector and one or more directors

⇒ The pressure coil of a wattmeter should be connected to the supply side of the current coil when
load impedance in high
load impedance is low
voltage is high
voltage is low

⇒

Match the following:

	List I		List II
A.	CLP	1.	Measure of μP clock speed
B.	SHELL	2.	Double sided double density
C.	DSDD	3.	Allows you to specify file as command processor
D.	Megahertz	4.	Microcode stored in ROM

A-4, B-3, C-2, D-1
A-3, B-4, C-2, D-1
A-1, B-2, C-3, D-4
A-2, B-3, C-4, D-1

⇒ Which of the following are the properties of a medium?
Permeability, flux, magnesium
Permittivity, permeability, insulation
Permeability, resistivity, conductivity
Permittivity, permeability, conductivity

⇒ VLF is generally used for
telegraphy
satellite communication
instrument landing system
all of the above

⇒ Consider the following materials

Nickel
Silver
Oxygen
Aluminium

The correct sequence in the order of decreasing permeability is
1, 4, 3, 2
1, 4, 2, 3
4, 1, 3, 2
4, 1, 2, 3

⇒ A two winding transformer is feeding a single phase half wave rectifier circuit. The load is purely resistive. The rms value of transformer secondary current is I_s and rms value of load current in I_rms. Then
I_s = I_rms irrespective of the value of firing angle
I_s = 0.5 I_rms irrespective of the value of firing angle
I_s = I_rms if firing angle is less than 30°
I_s = I_rms if firing angle is more than 30°

⇒ Noise which assumes great importance at high frequencies is
flicker noise
Johnson noise
transit-time noise
shot noise

⇒ Decimal 18.29 when converted int 10's complement will become
81.7707
81.7
81.777
81.077

⇒ A lag compensator provides attenuation in
very low frequency range
low frequency range
high frequency range
none of the above

⇒ - 56 is not a valid real constant in Fortran.
TRUE
FALSE

⇒ Consider the following stateme
1 and 2
2 and 3
3 and 4
4 and 5

⇒ Which of the following is invalid in Basic?
A ** B + - C
A ** B - C
A * B - C
A * B - C ** D

⇒ The standard FORTRAN exponential form of decimal number - 0.000000023 is
2.3 E - 8
-2.3 E - 8
2.3 E - 7
-2.3 E - 7

⇒ The input gate current of FET is closer to
few amperes
few milli amperes
few microamperes
negligibly smaller value

⇒ Binary number 11001 is equivalent to decimal number
35
15
105
25

⇒ To protect an SCR against high di/dt we connect
a capacitance in series with SCR
a capacitance in parallel with SCR
an inductance in parallel with SCR
an inductance in series with SCR