Question is ⇒ The numerical value of directivity of current element of half-wave dipole is 1.76 and 2.15 dB respectively. The directive gain of half-wave dipole over current element will be, Options are ⇒ (A) 3.91 dB, (B) 1.95 dB, (C) 0.39 dB, (D) 0.195 dB, (E) , Leave your comments or Download question paper.

Question is ⇒ The numerical value of directivity of current element of half-wave dipole is 1.76 and 2.15 dB respectively. The directive gain of half-wave dipole over current element will be, Options are ⇒ (A) 3.91 dB, (B) 1.95 dB, (C) 0.39 dB, (D) 0.195 dB, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The numerical value of directivity of current element of half-wave dipole is 1.76 and 2.15 dB respectively. The directive gain of half-wave dipole over current element will be
A.	3.91 dB [Wrong Answer]
B.	1.95 dB [Wrong Answer]
C.	0.39 dB [Correct Answer]
D.	0.195 dB [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For emitter-couple logic, the switching speed is very high because
negative logic is used
the transistors are not saturated when conducting
emitter-coupled transistors are used
multi-emitter transistors are used

⇒ In a TV receiver the raster is normal but there is no sound and quality of picture is poor. The defective part is
power supply
loudspeaker
AGC, video IF amplifier, RF amplifier
horizontal oscillator

⇒ In an op-amp comparator, the positive or negative output is
saturated
amplifier
unsaturated
any of the above

⇒ Wire-wound resistors are unsuitable for use at high frequencies because they
are likely to melt under excessive eddy current heat
exhibit unwanted inductive and capacitive effects
create more electrical noise
consume more power

⇒ A rectangular pulse is passed through an L.P.F. The response is a
triangular
trapezoidal function
sampling
Both (a) and (b)

⇒ In a microwave power measurement using bolometer, the principle of working is variation of
inductance with absorption of power
resistance with absorption of power
capacitance with absorption of power
cavity dimension with heat generated by power

⇒ In a transistor CE mode, V_CC = +30 V. If the transistor is in cut off region, V_CE =
+30 V
+20 V
10 V
zero

⇒ For a stable system having two or more gain crossover frequencies the phase margin is measured
at lowest gain crossover frequency
at highest gain crossover frequency
at the gain crossover frequencies
none of the above

⇒ The poles of an RC function
are simple and lie on jω axis
are simple and lie on negative real axis
may be complex conjugate
may be anywhere in s plane

⇒ Which of the following is not considered as a useful quantity in comparing noise performance of receivers?
Noise temperature
Noise figure
Noise resistance
Input noise voltage

⇒ The symbol in figure is
SUS
SBS
SCS
None of the above

⇒ In air friction damping
the air pressure opposes the motion of piston when it is moving inwards
the air pressure opposes the motion of piston when it is moving outwards
the air pressure opposes the motion of piston both when it is moving inwards as well as outwards
the air pressure may oppose or aid the motion of piston depending on the design

⇒ Electrical conductivity of metals expressed in ohm^-1 m^-1 is of the order of
10¹⁰
10⁵
10^-4
10^-6

⇒ Inverters find applications in
HVDC transmission
UPS
variable speed ac drives
all of the above

⇒ At high frequencies the output circuit of transistor amplifier reduces to
a lead network
a lag network
either (a) or (b)
neither (a) nor (b)

⇒ Which of the following expressions is invalid in Fortran?
IA + IB
IB * IC / ID
IA * B
- K * I + J

⇒ Ohmic range of metal film resistors is
1 to 100 ohms
10 to 1 K ohms
100 to 1 M ohms
100 to 100 M ohms

⇒

Assertion (A): When a PID controller is added to a system, the peak overshoot to step input cannot be determined easily.

Reason (R): Use of PID controller introduces a zero in the forward path.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ Two coil have their axis perpendicular to each other. The coefficient of coupling k is
1
0.5
more than 0 but less than 1
0

⇒ Bitter powder patterns prove the existence of domains.
TRUE
FALSE

⇒ The no. of FF required and the maximum decimal no. of a MOD-12 counter is
12, 12
4, 11
3, 6
4, 10

⇒ The ability of a radio receiver to discriminate between different input signals and to accept only one definite signal is called its
sensitivity
attenuation
selectivity
modulation

⇒ In a class C power amplifier
resonant frequency of tuned circuit is equal to fundamental frequency of pulsed waveform
resonant frequency of tuned circuit is half the fundamental frequency of pulsed waveform
resonant frequency of tuned circuit has no relation to the fundamental frequency of pulsed waveform
either (b) or (c)

⇒ A dc circuit breaker must use
natural commutation
forced commutation
both natural and forced commutation
either natural or forced commutation

⇒ The relation between thermionic emission current and temperature is known as
Richardson Dushman equation
Langmuir child law
Ohm's law
Boltzmann's law

⇒ In FM,
there is a large decrease in noise and hence increase in the signal to noise ratio
there is a large increase in noise and hence decrease in the signal to noise ratio
there is a large increase in noise and hence increase in the signal to noise ratio
there is a large decrease in noise and hence decrease in the signal to noise ratio

⇒ In a good voltage amplifier, its input impedance
must be high compared to the resistance of the source
must be low compared to the resistance of the source
must be equal to the resistance of the source
must be half the resistance of the source

⇒ In figure, which value of Z_L will cause maximum power to be transferred to the l
2 + j2 Ω
2 - j2 Ω
- 2 Ω
2 Ω

⇒ A bistable multivibrator
has no stable state
has one stable state
has two stable state
none of the above

⇒ The strength of controlled voltage source depends on
value of current elsewhere in the circuit
value of voltage elsewhere in the circuit
value of current or voltage elsewhere in the circuit
none of the above