Question is ⇒ The numerical value of directive gain may lie between, Options are ⇒ (A) 1 and + 1, (B) 0 and 1, (C) 0 and ∞, (D) 1 and ∞, (E) , Leave your comments or Download question paper.

Question is ⇒ The numerical value of directive gain may lie between, Options are ⇒ (A) 1 and + 1, (B) 0 and 1, (C) 0 and ∞, (D) 1 and ∞, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The numerical value of directive gain may lie between
A.	1 and + 1 [Wrong Answer]
B.	0 and 1 [Wrong Answer]
C.	0 and ∞ [Correct Answer]
D.	1 and ∞ [Wrong Answer]
View Answer 4 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a CD, the depth and width of each pit is
0.5 μm each
0.5 μm and 1 mm respectively
1 μm and 0.5 mm respectively
1 μm each

⇒ In a transistor the minimum and maximum values of β_dc are 100 and 121. The proper value of β_dc to be used to locate Q point is
100
121
110.5
110

⇒ Using 2's complement, the largest positive and negative number which can be stored with 8 bits are
+128 and -127
+128 and -128
+127 and -128
+127 and -127

⇒ The units of resistivity are ohm-metre.
TRUE
FALSE

⇒ Which of the following bus is used to transfer data from main memory to peripheral device?
DMA bus
Output bus
Input bus
Data bus

⇒ Calculate i(t) for t ≥ 0, assuming the switch has been in position A for a long time at t = 0, the switch is moved to positio
1 + e^{-5 x 10³t}
e^{-5 x 10³t}
1.11 e^{-5 x 10³t}
1.11 (1 - e^{-5 x 10³t})

⇒ JFET is also known as
linear device
square law device
inverse law device
logarithmic law device

⇒ Which one of the following bipolar transistors has the highest current gain bandwidth Product (f_r) for similar geometry?
NPN germanium transistor
NPN silicon transistor
PNP germanium transistor
PNP silicon transistor

⇒ The relative stability of a system is given by
gain margin alone
phase margin alone
both phase and gain margins
either (a) or (b)

⇒ A function f(t) = k is
stable
marginal stable
unstable
none

⇒

Assertion (A): In 8085 WR and RD signals are active high.

Reason (R): LOW WR means write operation and low RD means read operation.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ If the radiated power of AM transmitter is 10 kW, the power in the carrier for modulation index of 0.6 is nearly.
8.24 kW
8.47 kW
9.26 kW
9.6 kW

⇒ Temperature is analogous to
voltage
flux
charge
none of the above

⇒

Assertion (A): An SR latch has the problem of RAC condition

Reason (R): While designing a digital circuit RAC condition should be avoided.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ The refractive index of E layer, if angle of incidence is 30°
0.5
0.25
0
1

⇒ In a feedback series regular circuit, the output voltage is regulated by controlling the
magnitude of the I/P voltage
gain of the feed back BJT
reference Voltage
voltage drop across the series pass transistor

⇒ For edge triggering in flip flops, manufacturers use
RC circuit
direct coupled design
either RC circuit or direct coupled design
none of the above

⇒ Pilot-carrier transmission is one in which
only one sideband is transmitted
one sideband and carrier are transmitted
only two sidebands are transmitted
two sidebands as well as a trace of carrier are transmitted

⇒ A device which converts BCD to seven segment is called
encoder
decoder
multiplexer
none of these

⇒ In integral cycle control of ac regulators, the period of integral cycle control, i.e., (m + n) T should be
less than mechanical or thermal time constant of the system
more than the mechanical or thermal time constant of the system
more or less than the mechanical or thermal time constant
very high

⇒ In 8086 the flag which enables or disables external interrupts is
IF
DF
TF
CF

⇒ An ac circuit has two branches in parallel. The impedances of the two branches are equal. The p.f. of one branch is 0.8 lagging and 0.8 leading. The overall p.f. is
zero
0.5 lagging
1
0.7 lagging

⇒ Select the correct relation
∇(AB) = A ∇ B + B ∇ A
∇ . (AB) = ∇ A . B + A ∇ B
∇ x (AB) = ∇ A x B + A ∇ B
All of the above

⇒ A moving iron voltmeter reads 250 V when connected to 250 V dc. If connected to 250 V 50 Hz, the voltmeter reading is likely to be
250 V
252 V
248 V
210 V

⇒ In a homogeneous magnetic field H of a solenoid, the core carries a magnetic dipole moment M per unit volume equal to
μ₀ H
μ_r H
(μ_r - 1) H
μ_oμ_r H

⇒

Match the following:

	Microwave Measuring Instruments		Measurements Effected
A.	Bolometer	1.	Reflection coefficients
B.	VSWR meter	2.	Half power beam widths
C.	Cavity wave meter	3.	Microwave power
D.	Pattern recorder	4.	Microwave frequency

A-2, B-1, C-4, D-3
A-3, B-1, C-4, D-2
A-2, B-4, C-1, D-3
A-3, B-4, C-1, D-2

⇒ The V-I characteristic of a semi-conductor diode is shown in figure. From this figure it can be concluded
The diode is a silicon diode
The diode is a germanium diode
Break down voltage of the diode is 0.7 V
At 1 V rated current will pass through the diode

⇒ It is desired to display the digit 7 using a seven segment display. The LEDs to be turned on are
a, b, c
b, c, d
c, d, e
a, b, d

⇒ A transmission line terminates in two branches, each of length λ/4, as shown. The branches are terminated by 50Ω loads. The lines are lossless and have the characteristics impedances shown. Determine the impedance Z₁ as seen by the so
200Ω
100Ω
50Ω
25Ω

⇒ A sample of N type semiconductor has electron density of 6.25 x 10⁸/cm² at 300 K. If the intrinsic concentration of carriers in this sample is 2.5 x 10¹³/cm³ at this temperature, the hole density works out to be
10⁶/cm³
10⁸/cm³
10¹⁰/cm³
10^l2/cm³