Question is ⇒ The network shown in figur, Options are ⇒ (A) reciprocal, (B) reciprocal and symmetrical, (C) non-reciprocal, (D) unsymmetrical, (E) , Leave your comments or Download question paper.

Question is ⇒ The network shown in figur, Options are ⇒ (A) reciprocal, (B) reciprocal and symmetrical, (C) non-reciprocal, (D) unsymmetrical, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The network shown in figur
A.	reciprocal [Wrong Answer]
B.	reciprocal and symmetrical [Wrong Answer]
C.	non-reciprocal [Correct Answer]
D.	unsymmetrical [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The breakdown voltage in a zener diode
is almost constant
is very small
may destroy the diode
decreases with increase in current

⇒ Which of the following is not a valid variable in FORTRAN 77?
BRG
VS
VS 3A
3 VSA

⇒ A TR (transmitter receiver) tube has
low loss for low power signals and high
high loss for low power signals and low loss for high level signal
low loss for both low level and high level signals
high loss for both low level and high level signals

⇒ Laplace transform of a unit doublet U_-2 (t) is
1/s
s
0
1

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None

⇒ In n type MOSFET, the substrate
is p type
is n type
is metallic
may be p or n type

⇒ A microwave junction is matched at all ports if the S matrix
has all diagonal elements zero
has all diagonal elements equal but not zero
has all diagonal elements complex
is Hermitian

⇒ A cut set schedule shows
incidence of branches to loops
incidence of branches to nodes
incidence of nodes to loops
none of the above

⇒ In the stabilized reactance modulators AFC system
the discriminator must have a fast time constant to prevent demodulation
the higher discriminator frequency the better the oscillator frequency stability
the discriminator frequency must not be too low, or the system will fail
phase modulation is converted into FM by the equalizer circuit

⇒ An iron specimen has µ_r = 1000 when B = 0.3 T. If B = 0.35 T, µ_r
will be 1000
will be less than 1000
will be more than 1000
may be more or less than 1000

⇒ Consider the following circuits. Assume all gates to have finite propagation d
(1) only
(1) and (2) only
(2) (3) and (4) only
All (1) (2) (3) and (4)

⇒ In figure, voltage across R₂ = + 10 V. If V_BE = 0.7 V and V_E = 0.7 V and R_E = 10 kΩ, current through R_{E1 mA
0.93 mA
2 mA
1.86 mA}

⇒ The output of a Mealy system is 1 if there has been a pattern of 11000, otherwise 0. The minimum state for this system is :
4
5
6
7

⇒ On which bands, do the optical fibers operate?

Ultra violet band
Ultra high frequency band
Visible light band
Infrared band

Select the correct answer from the codes given below:
1 only
1 and 2 only
1, 2 and only
1, 3 and 4

⇒ If A = 16 ∠64°, (A)^0.5 is
4∠64°
4∠8°
4∠128°
4∠32°

⇒ The timing difference between a slow memory and fast processor can be resolved if
processor is capable of waiting
external buffer is used
either (a) or (b)
neither (a) nor (b)

⇒ Which of the following output configurations are available in a TTL gate?

Open collector output
Totem pole output
Tristate output

Select the correct answer from the codes given below:
1 only
1 and 2 only
2 and 3 only
1, 2 and 3

⇒ The voltage e_o indicated in the figure has been measured by an ideal voltmeter. Which of the following can be calcula
Bias current of inverting input only
Bias current of inverting and non-inverting inputs only
Input offset current only
Both the bias currents and the I/P offset current

⇒ If V_dc1 is the dc output voltage in half wave controlled rectifier circuit feeding resistive load and V_dc2 is the dc output voltage in full wave controlled rectifier circuit (M - 2 connection) feeding resistive load, then
V_dc1 = 0.5 V_dc2 for all values of firing angle
V_dc1 = V_dc2 for all values of firing angle
V_dc1 ≤ 0.5 V_dc2 for all values of firing angle
V_dc1 ≥ 0.5 V_dc2 for all values of firing angle

⇒ The frequency deviation of a FM signal produced from PM is
identical to that of FM signal produced by direct method
larger than that of a FM signal produced by direct method
directly proportional to the peak amplitude and the frequency of modulating signal
directly proportional to the peak amplitude of the modulating signal

⇒ Ferroelectric materials are those which
cannot be polarized
have a permanent polarization
have a_e equal to zero
have μ_p = 0

⇒ The pole-zero configuration of the given figure can be
lag compensator
lead compensator
lead-lag compensator
series compensator

⇒ In figure we need an ac ground. The proper value of
1000 μF
100 μF
10 μF
1 μF

⇒ Aperture circuit produces __________ in sample hold circuit.
the total sampling time
delay between the instance at which hold command is initiated and the instance at which O/P starts tracking I/P
the time taken by O/P to settle within the specified 1% error band, that of the I/P
time required by holding capacitor to reach upto the level close to input

⇒ Two numbers are 131 ± 5 and 629 ± 3. The sum of the numbers with range of doubt is
760 ± 8
760 ± 2
760 + 8
760 - 8

⇒ Calculate cut off frequency for dominant mode in rectangular waveguide if dimensions are a = 2, b = 1 cm.
7.5 GHz
1.5 GHz
15 GHz
150 GHz

⇒ In radio receiver, the maximum contribution to noise is from
mixer stage
power supply
power amplifier
equally from above three

⇒ Complex pole in z-plane is as shown below. This is the pole diagram for ________
Decaying sinusoidal sequence
Growing sinusoidal sequence
Decaying non sinusoidal sequence
Growing non sinusoidal sequence

⇒ A function table is required in very large numbers the memory most switched for this purpose would be
ROM
PROM
EPROM
EAROM

⇒ How many maximum number of functions can be defined with two symbols which are Boolean in nature:
4
8
2
16