Question is ⇒ The multivibrator circuit that has a typical application of converting sinusoidal input into a square wave output is, Options are ⇒ (A) emitter coupled binary, (B) Schmitt trigger, (C) monoshot multivibrator, (D) free-running multivibrator, (E) , Leave your comments or Download question paper.

Question is ⇒ The multivibrator circuit that has a typical application of converting sinusoidal input into a square wave output is, Options are ⇒ (A) emitter coupled binary, (B) Schmitt trigger, (C) monoshot multivibrator, (D) free-running multivibrator, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The multivibrator circuit that has a typical application of converting sinusoidal input into a square wave output is
A.	emitter coupled binary [Wrong Answer]
B.	Schmitt trigger [Correct Answer]
C.	monoshot multivibrator [Wrong Answer]
D.	free-running multivibrator [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The box on the external left of the title bar of menu is called control menu box.
TRUE
FALSE

⇒ The main disadvantage of the two-hole directional coupler is
poor directivity
narrow bandwidth
high standing wave ratio
low directional coupling

⇒ A magnetron requires an external magnetic field with flux lines parallel to axis of cathode
TRUE
FALSE

⇒ The load circuit of a single phase full bridge inverter
must be underdamped
must be overdamped
may be underdamped or overdamped
may be any type of load

⇒ In saturation region JFET acts like a
bipolar device
short circuit
switch
resistance

⇒ Consider the following statements, regarding an OP AMP:

All types of negative feedback reduce non-linear distortion.
All types of negative feedback reduce the output offset voltage.
Non-inverting (current and voltage) feedback increases the input impedance.
Inverting (current and voltage) feedback decreases input impedance.

Which of the above statements is/are correct?
1 only
2 and 3 only
2 and 4 only
1, 2, 3 and 4

⇒ If V = 20 + j20, then log_e(A) A is
3.342 + j 45
28.28 ∠45°
400 ∠45°
3.342 + j 0.785

⇒ For low impedance SAW filter the most suitable material for substrate of SAW filter is
PZT ceramics
ZnO
Lithium titanate
Lithium neobate

⇒ In a minimum function
the degree of numerator and denominator are equal
the degree of numerator and denominator are unequal
the degree of numerator is one more than degree of denominator
the degree of numerator is one less than degree of denominator

⇒ The capacitor filter provides poor voltage regulation because
the increase in ripple with load current causes a decrease in average voltage
the increase in ripple with load current causes a increase in average voltage
filter promotes ripple at peak voltage
none of the above

⇒ The total number of pins in 8085 are
20
30
40
50

⇒ Decimal number 9 in gray code =
1100
1101
110
1111

⇒ The resistance of the circuit shown is figur
5 Ω
More than 6 Ω
More than 4 Ω
Between 6 and 7 Ω

⇒ Consider the following statements: The radar pulse must be flat topped to

allow accurate range measurement
allow good minimum range
prevent frequency changes in magnetron
make the returned echoes easier to distinguish from noise.

Which of the above are correct?
1, 2, 3, 4
1, 2, 3
1, 2
1, 3, 4

⇒ The phase angle curve of G(jω) H(jω) can be drawn
by adding the phase angle curves of individual factors
by subtracting the phase angle curves of individual factors
by multiplying the phase angle curves of individual factors
by dividing the phase angle curves of individual factors

⇒ In an n-p-n transistor, the majority carriers in the base are
electrons
holes
both holes and electrons
either holes or electrons

⇒ The resistivity of intrinsic semiconductor material is about
10⁵ ohm-m
10³ ohm-m
100 ohm-m
1 ohm-m

⇒ The system with given pole-zero diagra
casual
non-casual
both sided
not-possible

⇒ In a lead acid cell the density of the acid gives an indication of
the level of the acid
the eventual damages caused to the plates
the charge of the battery
the e.m.f. of the battery

⇒

Assertion (A): The output of a NOR gate is equal to the complement of OR of input variables.

Reason (R): A XOR gate is a universal gate.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒

Match the following:

	List I		List II
A.	Laser	1.	Emits monochromatic light of low intensity
B.	Solar cell	2.	Consumes electrical power due to incident light
C.	Photodiode	3.	Delivers power to a load
D.	LED	4.	Emits monochromatic light of high intensity

A-4, B-3, C-1, D-2
A-3, B-4, C-2, D-1
A-4, B-3, C-2, D-1
A-3, B-4, C-1, D-2

⇒ The temperature of cathode is increased from 2500K to 2600K. The increase in thermionic emission current is about
0.001
0.04
0.5
1.5

⇒ The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is
500 Hz
700 Hz
300 Hz
1400 Hz

⇒ In 8085 the data is stored in the stack on
First in First Out basis
Last in First Out basis
First in Last Out basis
Last in Last Out basis

⇒ Which of the following is the poorest conductor of electricity?
Aluminium
Nichrome
Copper
All of the above

⇒ A thyristor has a turn on time of 6 μs. If the anode circuit is inductive, the turn on time will be
6 μs
less than 6μs
more than 6 μs
either 6 μs or less

⇒ On modulating a carrier of frequency f_c by an audio signal f_s, the following components has result
Amplitude modulation (DSB)
Single sideband modulation
Frequency modulation only
Amplitude modulation or frequency modulation

⇒ In 8085 microprocessor, what is the length of Data Buffer Register?
6 bits
8 bits
12 bits
16 bits

⇒ An insulator will conduct when the
voltage applied is more than the breakdown voltage
temperature is raised to very high level
either (a) or (b) above
none of the above

⇒ For the factor (1 + 0.5 jω) the corner frequency is
1 rad/sec
0.5 rad/sec
2 rad/sec
0.25 rad/sec