Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The modulus of elasticity for copper is more than that of lead. It can be, therefore, concluded that copper is |

A. | More elastic [Correct Answer] |

B. | More plastic [Wrong Answer] |

C. | Less elastic [Wrong Answer] |

D. | Less plastic [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :Devendra Yadav Said on 2018-09-30 08:15:12E refers to measure of stiffness. It means higher the E less plastic the material. !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A body having similar properties throughout its volume is said to be

Homogeneous

Isotropic

Continuous

Anisotropic

⇒ The shear force on a beam

Causes linear transverse development

Causes separation of fibres

Causes rupture in the beam section

Results in rotation of the planes

⇒ As compared to uniaxial tension or compression, the strain energy stored in bending is only

1/8

1/4

1/3

1/2

⇒ If the width

*b*and depth

*d*of a beam simply supported with a central load are interchanged, the deflection at the centre of the beam will be changed in the ratio of.

b/d

d/b

(d/b)2

(b/d)2

⇒ The shape of the bending moment diagram over the length of a beam, carrying a uniformly distributed load is always.

linear

parabolic

cubical

circular.

⇒ Energy stored per unit volume in a stretched wire is

1/2 Load x Strain

Load x Strain

Stress x Strain

1/2 Stress x Strain

⇒ The Poisson's ratio for steel varies from

0.23 to 0.27

0.25 to 0.33

0.31 to 0.34

0.32 to 0.42

⇒ The bending moment on a section is maximum where shear force is

Zero

Minimum

Maximum

Changing sign

⇒ A live load is

One that occurs due to deaci bodies

One that does not exist actually

One that remains constant

One that does not remain constant

⇒ The ratio of elongations of a conical bar due to its own weight and that of a prismatic bar of the same length, is

1/2

1/3

1/4

1/5

⇒ The basic perfect frame is

Triangle

Rectangle

Hexagon

Square

⇒ Hooke's law states that stress and strain are.

directly proportional

inversely proportional

curvilinearly related

none of these

⇒ The distance between the centres of adjacent rivets in the same row, is called.

pitch

lap

gauge

staggered pitch

⇒ The ratio of the tensile stress developed in the wall of a boiler in the circumferential direction to the tensile stress in the axial direction, is.

4

3

2

1

⇒ A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear force in the wooden log is.

50 N at each end

50 N at the centre

100 N at the centre

none of these.

⇒ A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10, 000 kg, the corresponding maximum shearing stress being 30 kg/cm

^{2}. The depth of the beam is

15 cm

20 cm

25 cm

30 cm.

⇒ A simply supported beam carries two equal concentrated loads

*W*at distances

*L*/3 from either support. The maximum bending moment.

WL/3

WL/4

5WL/4

3WL/12

⇒ Buckling load for a given column depends upon

length of column only

least lateral dimension only

both length and least lateral dimension

none of the above

⇒ The property of metal which allows it to deform continuously at slow rate without any further increase in stress is known as

fatigue

creep

plasticity

resilience

⇒ The ability of a material to resist deformation is said to be

Strength

Toughness

Plasticity

Brittleness

⇒ The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is

one-half of the radius

one-third of the radius

one-quarter of the radius

one-fifth of the radius

⇒ In a solid arch, shear force acts.

vertically upwards

along the axis of the arch

perpendicular to the axis of arch

tangentially to the arch

⇒ The impact test assess the property of material such as its

Hardness

Strength

Toughness

Brittleness

⇒ The ratio of the maximum deflection of a cantilever beam with an isolated load at its free end and with a uniformly distributed load over its entire length, is.

1

24/15

3/8

8/3

⇒ A beam is said to be of uniform strength, if.

B.M. is same throughout the beam

shear stress is same throughout the beam

deflection is same throughout the beam

bending stress is same at every section along its longitudinal axis

⇒ In a thin cylindrical shell, the ratio of longitudinal stress to hoop stress is

0.5

1

2

4

⇒ The reaction at support

*A*of the beam shown in below figure, is

zero

5 T

10 T

1 T

⇒ A wire can be broken by applying a load of 20 kg weight. The force required to break the wire of twice the diameter is

20 kg weight

5 kg weight

50 kg weight

160 kg weight

⇒ Due to rise in temperature in a three hinged arch, induced stress is

direct compressive

direct tensile

shear

none of the above

⇒ At a point in a steel member, the major principal stress is 2000 kg/cm2 and the minor principal stress is compressive. If the uni-axial tensile yield stress is 2500 kg/cm2, then the magnitude of the minor principal stress at which yielding will commence, according to the maximum shearing stress theory, is

1000 kg/cm2

2000 kg/cm2

2500 kg/cm2

500 kg/cm2