Question is ⇒ The minimum number of comparators required to build an 8 bit flash ADC is, Options are ⇒ (A) 8, (B) 63, (C) 255, (D) 256, (E) , Leave your comments or Download question paper.

Question is ⇒ The minimum number of comparators required to build an 8 bit flash ADC is, Options are ⇒ (A) 8, (B) 63, (C) 255, (D) 256, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The minimum number of comparators required to build an 8 bit flash ADC is
A.	8 [Wrong Answer]
B.	63 [Wrong Answer]
C.	255 [Correct Answer]
D.	256 [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a Gunn diode oscillator drift velocity of electron is 10⁷ cm/s and active region length is 10 x 10^-4 cm. The natural frequency of oscillation is
1 MHz
10 MHz
1 GHz
10 GHz

⇒ AM transmitter employing low level modulation
uses class C amplifier for amplification
requires higher audio power
has a poor efficiency
has a higher efficiency

⇒ To measure dielectric loss you would use
Anderson bridge
Kelvin bridge
Schering bridge
Maxwell's bridge

⇒ Which of the following best represents the bandwidth of an actual op-amp?
100 Hz to 1 MHz
0 Hz to 100 kHz
0 Hz to 10 MHz
0 Hz to infinity

⇒ The constant magnitude of G(s) plane are
a family of straight horizontal lines
a family of straight inclined lines with positive slope
a family of straight inclined lines with negative slope
a family of circles

⇒ Consider the Boolean expression X = ABCD + ABCD + ABCD + ACBD The simplified form of X is
C + D
BC
CD
B

⇒ The circuit show
voltage series feedback amplifier
transconductance amplifier
transresistance amplifier with open circuit mutual resistance R_F
transresistance amplifier with short circuit mutual resistance R_F

⇒ In a transistor with normal bias
the emitter junction has a low resistance
the emitter junction has a very high resistance
the emitter junction supplies majority carries into the base region
none of the above

⇒ The voltage gains of an amplifier without feedback and with negative feedback respectively are 100 and 20. The percentage of negative feedback (β) would be
0.4
0.05
0.2
0.8

⇒ j⁶ =
j
j²
j³
- j

⇒ In a vacuum tube, the transit time of electron between cathode and anode is important at
low frequencies
high frequencies
both (a) and (b)
frequencies which are neither very low nor very high

⇒ One of the advantages of base modulation over collector modulation of a transistor class C amplifier is
improved efficiency
better linearity
high power output per transistor
the lower modulating power requirement

⇒ An electron in the conduction band
has higher energy than the electron in the valence band
has lower energy than the electron in the valence band
loses its charge easily
jumps to the top of the crystal

⇒ Refractive index of glass is 1.5. Find the wavelength of a beam of light with a frequency of 10¹⁴ Hz in glass. Assume velocity of light is 3 x 10⁸ m/sec in vacuum.
4 μm
3 μm
2 μm
1 μm

⇒ In the circuit shown in the figure the power dissipated in 30 Ω resistor will be maximum if the value of
30 Ω
10 Ω
9 Ω
zero

⇒ A lossless transmission line is 50 cm long and operates at a frequency of 500 MHz. Inductance and capacitances present in a line are 0.5 μH/m and 200 pF/m. Phase constant and phase velocity are respectively.
5p, 2p x 10⁸ m/sec
5p, 10⁸ m/sec
31.4, 10⁸ m/sec
31.4, 2p x 10⁸ m/sec

⇒ Which is correct with respect to computer memory?
Only a particular address can have a particular memory
Any address can have any memory
To read a word from computer memory, it is not necessary to specify a location
None of the above

⇒ Which is not purpose of modulation?
Effective radiation
Multiplexing
Narrow band
Increase in signal power

⇒

Match the following:

	List I (Library function in Pascal)		List II (Type of argument)
A.	ROUND X	1.	X in radians
B.	ABS X	2.	X real
C.	SQR X	3.	X real or integer
D.	SIN X

A-2, B-3, C-3, D-1
A-2, B-3, C-1, D-3
A-3, B-2, C-2, D-1
A-2, B-3, C-2, D-1

⇒ Which of the following types of noise assumes greater importance at high frequencies?
Transit time noise
Shot noise
Impulse noise
Random noise

⇒ BCD input 1000 is fed to a 7 segment display through a BCD to 7 segment decoder/driver. The segments which will lit up are
a, b, d
a, b, c
all
a, b, g, c, d

⇒ If A = 3 + j1, A⁴
100 ∠18.43°
100 ∠73.72°
10 ∠18.43°
10 ∠73.72°

⇒ For telegraphy the most commonly used modulation system is
FSK
two tone modulation
PCM
single tone modulation

⇒ The point P in the following figure is stock at 1. The output f wil
ABC
A
AB C
A

⇒ In Jone chopper, the commutating element
is a capacitor
is a capacitor and an inductor
is a capacitor and an auto transformer
none of the above

⇒ For a wave propagating in air filled rectangular waveguide.
guide wavelength is never less than free space wavelength.
wave impedance is never less than the free space impedance
TEM mode is possible if the dimension of the waveguide are properly chosen.
propagation constant is a real quantity.

⇒ The intrinsic resistivity of silicon at 300 K is about
1 Ω-cm
400 Ω-cm
10000 Ω-cm
230000 Ω-cm

⇒ Hall effect is observed in a specimen when it is carrying current and is placed in a magnetic field. The resultant electric field inside the specimen is
normal to both current and magnetic field
in the direction of current
antiparallel to magnetic field
in arbitrary direction

⇒ Read the following statements about TWT

It uses thermionic emission.
It uses an attenuater.
It is inherently a resonant device.
It has broad bandwidth.

Which of the above are correct?
1, 2, 3 and 4
1, 2 and 3
1, 3 and 4
1, 2 and 4

⇒ At night the ionosphere can be considered to be consisting of
D, E, F₁ and F₂ layers
D, E, F₁ layers
D, E, F₂ layers
E and F₂ layers