Question is ⇒ The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is, Options are ⇒ (A) 4.0, (B) 2.0, (C) 1.0, (D) 0.5, (E) , Leave your comments or Download question paper.

Question is ⇒ The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is, Options are ⇒ (A) 4.0, (B) 2.0, (C) 1.0, (D) 0.5, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is
A.	4.0 [Wrong Answer]
B.	2.0 [Wrong Answer]
C.	1.0 [Wrong Answer]
D.	0.5 [Correct Answer]
View Answer 12 -4 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The condition for maximum efficiency for a D.C. generator is
eddy current losses = stray losses
hysteresis losses = eddy current losses
copper losses = 0
variable losses = constant losses

⇒ Compensating winding in a D.C. machine is placed
on yoke in the pole faces
on yoke in the interpolar gap
on armature
none of the above

⇒ Field winding of a D.C. series motor is usually provided with thick wire
to provide large flux
to reduce the use of insulating materials
as it carries large load current
in order to reduce eddy current

⇒ Which D.C. motor is preferred for elevators ?
Shunt motor
Series motor
Differential compoun.d motor
Cumulative compound motor

⇒ If t be the thickness of the laminations, then eddy current loss in a generator. will vary as
¹/_t
¹/_t²
t
t²

⇒ In D.C. machines fractional pitch winding is used
to improve cooling
to reduce copper losses
to increase the generated e.m.f.
to reduce the sparking

⇒ In variable speed motor
a stronger commutating field is needed at low speed than at high speed
a weaker commutating field is needed at low speed than at higt speed
same commutating field is needed at low speed than at high speed
none of the above is correct

⇒ Between Field's test and Hopkinson's test the main common thing is that both
use negligible power
are regenerative tests
need two similar mechanicallycoupled motors
need two electrically coupled series motors

⇒ D.C. motor is to drive a load which has certain minimum value for most of the time and some peak value for short duration. We will select the
series motor
shunt motor
compound motor
any of the above

⇒ What will happen if the back e.m.f. of a D.C. motor vanishes suddenly?
The motor will stop
The motor will continue to run
The armature may burn
The motor will run noisy

⇒ The condition for maximum power in case of D.C. motor is
back e.m.f. = 2 x supply voltage
back e.m.f. = 1/2 x supply voltage
supply voltage = 1/2 x back e.m.f.
supply voltage = back e.m.f.

⇒ A face plate starter is employed for starting
induction motor
universal motor
synchronous motor
d.c. series motor

⇒ Which loss in a D.C. generator varies with load ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ The speed of a D.C. motor, under constant load conditions, is affected by
back e.m.f.
field flux
armature current
none of the above

⇒ The speed of a series motor at no load is
infinity
4000 r.p.m.
2000 r.p.m.
1000 r.p.m.

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?
hysteresis loss
field copper loss
armature copper loss
eddy current loss

⇒ The generated e.m.f. and the current are in the opposite direction in case of
d.c. generators
d.c. motors
both (a) and (b)
none of the above

⇒ Speed ,control by varying the armature circuit resistance, in a D.C. motor, provides a
constant torque drive
variable torque drive
constant power drive
variable power drive

⇒ In a differentially compounded D.C. motor, if shunt field suddenly opens
the motor will first stop and then run in opposite direction as series motor
the motor will work as series motor and run at slow speed in the same direction
the motor will work as series motor and run at high speed in the same direction
the motor will not work and come to stop

⇒ The mechanical power developed by a D.C. motor is equal to
power input + losses
back e.m.f. X armature current
power output X losses
power output X efficiency

⇒ Which of the following tests can be used to determine no-load losses in a D.C. shunt motor ?
Running down test
Swinburne's test
Field test
Brake test

⇒ D.C. generators are normally designed for maximum efficiency around
full-load
rated r.p.m.
rated voltage
all of the above

⇒ For a D.C. shunt motor if the excitation is changed
torque will remain constant
torque will change but power will remain constant
torque and power both will change
torque, power and speed, all will change

⇒ During rheostat braking of D.C. series motors
motor is run as a generator
motor is reversed in direction
motor is run at reduced speed

⇒ While starting a differential compound motor, it is best to short the series field in order to avoid
excessive starting period
motor starting in wrong direction
tripping of the circuit breaker
large in rush of current

⇒ A shearing machine has cyclic load consisting of intermittent light and henry loads. Which of the following D.C. motor will be suitable for this purpose?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ Speed control of a cumulatively compounded D.C. motor can be effected through change of
field resistance
armature resistance
armature voltage
any of the above

⇒ The speed of a D.C. series motor is
proportional to the armature current
proportional to the square of the armature current
proportional to field current
inversely proportional to the armature current

⇒ The speed of a D.C. motor can be varied by varying
field current
applied voltage
resistance in series with armature
any of the above

⇒ The retardation test is applicable to shunt motors and generators and is used to find
the copper losses
the stray losses
the friction losses
the eddy current losses