Question is ⇒ The maximum power handling capacity of a resistor depends on, Options are ⇒ (A) total surface area, (B) resistance value, (C) thermal capacity of the resistor, (D) resistivity of the material used in the resistor, (E) , Leave your comments or Download question paper.

Question is ⇒ The maximum power handling capacity of a resistor depends on, Options are ⇒ (A) total surface area, (B) resistance value, (C) thermal capacity of the resistor, (D) resistivity of the material used in the resistor, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The maximum power handling capacity of a resistor depends on
A.	total surface area [Wrong Answer]
B.	resistance value [Wrong Answer]
C.	thermal capacity of the resistor [Correct Answer]
D.	resistivity of the material used in the resistor [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Metals approach superconductivity conditions
near absolute zero temperature
near critical temperature
at triple point
under the conditions of high temperature and pressure

⇒ Inverters find applications in
HVDC transmission
UPS
variable speed ac drives
all of the above

⇒ The most important set of specifications of transformer oil include
dielectric strength and viscosity
dielectric strength and flash point
viscosity and flash point
flash point and viscosity

⇒ When a trivalent impurity is added, the semiconductor becomes
p type
n type
intrinsic
neutral

⇒ In a ripple counter,
whenever a flip flop sets to 1, the next higher FF toggles
whenever a flip flop sets to 0, the next higher FF remains unchanged
whenever a flip flop sets to 1, the next higher FF faces race condition
whenever a flip flop sets to 0, the next higher FF faces race condition

⇒ In the forward blocking region of a silicon, controlled rectifier, the SCR is
in the off-state
in the ON state
reverse biased
at the point of breakdown

⇒ Which of the following is not an application software?
MS Word
DBMS
Worksheet
Lisp

⇒ Pre-emphasis and De-emphasis is done by using R-C circuit.
TRUE
FALSE

⇒ For a reflection co-efficient of 0.5, the value of SWR is
-1
1
2
3

⇒

Assertion (A): Negative feedback reduces the bandwidth of an amplifier

Reason (R): Negative feedback stabilizes the gain of an amplifier

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ For a series R-L-C circuit tuned at resonant frequency which of the following statements is correct?
The voltage across inductance is greater than applied voltage
The voltage across capacitance is greater than applied voltage
The voltage across both inductance and capacitance is greater than applied voltage
The voltage across both inductance and capacitance is less than applied voltage

⇒ The circuit in figure has reached steady values with switch open. If switch is closed at t = 0 the voltage across 2 μF capacitance at t = 0^{+zero
4 V
6 V
10 V}

⇒

Assertion (A): In a power divider S_H = 0, S₂₁ = 0.707 = S₃,

Reason (R): In a power divider the input port (i.e., port 1) is matched and incident power is equally divided in output ports 2 and 3

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The z-transform of a particular signal is gi
casual and stable
non-casual and stable
non-casual and unstable
casual and unstable

⇒ A silicon (PN) junction at a temperature of 20°C has a reverse saturation current of 10 pico Ampere. The reverse saturation current at 40°C for the same bias is approximately.
30 pA
40 pA
50 pA
60 pA

⇒ In a megger the moving coil meter has a permanent magnet.
TRUE
FALSE

⇒ The use of microprocessor control in automobiles results in
improved fuel economy
improved car control
advanced information system for driver
all of the above

⇒ In floating point representation, the accuracy is
10 bit
9 bit
8 bit
6 bit

⇒ High IF in a superheat receiver
improves selectivity
increases tracking problems
decreases tracking problems
reduces adjacent channel rejection

⇒ As the ratio R_f/R_L increases the efficiency of a rectifier increases.
TRUE
FALSE

⇒ When deflecting torque and braking torque in an energy meter are zero,
the disc rotates at steady speed
the disc is stationary
the disc accelerates
the disc retards

⇒ The current gain of a BJT is
g_m r₀
g_m/r₀
g_m r_p
g_m/r_p

⇒ Which part of radio spectrum is more crowded?
Lower frequency part
Higher frequency part
Both (a) and (b)
None of these

⇒ Which one of the following statement is correct?
Both Laplace's (L) and Poisson's (P) equation are non linear
L is non linear but P is linear
L is linear but P is non linear
L, P both is linear

⇒

Match the following:

	List I		List II
A.	200 MHz	1.	SHF
B.	20 GHz	2.	UHF
C.	500 kHz	3.	VHF
D.	500 MHz	4.	MF

A-3, B-1, C-4, D-2
A-3, B-2, C-4, D-1
A-3, B-4, C-1, D-2
A-3, B-4, C-2, D-1

⇒ The current through a PN Junction diode with v volts applied to the P region to the N region, where (I₀ is the reverse saturation current to the diode, m the ideality factor, k the Boltzmann constant, T the absolute temperature and q the magnitude of charge on an electron) is
I₀ (e^-qv/mkT - 1)
I₀ e^-qv/mkT
I₀ (1 - e^qv/mkT)
I₀ (e^qv/mkT - 1)

⇒ Time delay of a TTL standard family is about
180 ns
50 ns
18 ns
3 ns

⇒ Both ROM and RAM can be accessed randomly.
TRUE
FALSE

⇒ The function shown in the given Figure can be writte
sum of two sinusoidal functions
sum of two sinusoidal functions one originating at t = 0 and the other at t = 1
difference of two sinusoidal functions one originating at t = 0 and the other at t = 1
none of the above

⇒ A bridge rectifier circuit has input of 50 Hz frequency. The load resistance is R_L and filter capacitance is C. For good output wave shape, the time constant R_LC should be at least equal to
10 ms
20 ms
50 ms
100 ms