Question is ⇒ The material used for the magnet of moving coil cone type loudspeaker is, Options are ⇒ (A) steel alloy, (B) soft iron, (C) hard steel, (D) Alnico, (E) , Leave your comments or Download question paper.

Question is ⇒ The material used for the magnet of moving coil cone type loudspeaker is, Options are ⇒ (A) steel alloy, (B) soft iron, (C) hard steel, (D) Alnico, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The material used for the magnet of moving coil cone type loudspeaker is
A.	steel alloy [Wrong Answer]
B.	soft iron [Wrong Answer]
C.	hard steel [Wrong Answer]
D.	Alnico [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following are applications of position control systems?
Control of sheet and metal thickness in hot rolling mill
Missile guidance of ships
Radar tracking system
All of the above

⇒

Assertion (A): Inverse Laplace transform can be found from P(s) by inversion integral.

Reason (R): The function f(t) is assumed to be zero for t < 0.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ If antenna diameter is increased four times, the maximum range is increased by a factor of
2
2
4
0.2

⇒ In TE mode of waveguide E_z = 0
TRUE
FALSE

⇒ If velocity of sound waves in air at 0°C is 330 m/s, the velocity at 40°C is about
330 m/s
334 m/s
353 m/s
380 m/s

⇒ A depletion type NMOS is operated in enhancement mode. V_p = - 4 volts. For V_GS = + 3 volts as V_DS is increased, I_D becomes nearly constant when V_ps equals
1 volt
3 volts
4 volt
7 volts

⇒ The circuit in figure is
resonant commutation
self commutation
load commutation
auxiliary commutation

⇒ A 300 MHz plane EM wave is propagating in free space. The wave is incident normally on an infinite copper slap. The antenuation constant for the wave is (σ_copper = 5.8 x 10⁷ mho/ m). The skin depth is
0.005 x 10^-3 m
0.0038 x 10^-3m
0.0028 x 10^-3 m
0.0024 x 10^-3 m

⇒ The phase angle curve of G(jω) H(jω) can be drawn
by adding the phase angle curves of individual factors
by subtracting the phase angle curves of individual factors
by multiplying the phase angle curves of individual factors
by dividing the phase angle curves of individual factors

⇒ The dominant mode in a rectangular wave-guide is
TE₀₁
TM₀₁
TE₁₀
TM₁₁

⇒ Consider the following statements

An assembler is a program having assembly language program as input and machine language program as output.
A macro assembler is an assembler with additional macro facilities.
A cross assembler for a μP X is an assembler which executes on source microcomputer with a different CPU than X bit generates code for X.
Assemblers generally do not provide macro facilities.

Of the above statement
All are correct
only 1, 2, 3 are correct
only 1, 2, 4 are correct
only 1, 3, 4 are correct

⇒ An m derived low pass filter has f_c = 1000 Hz and m = 0.6. This filter will have infinite attenuation at
f = 1250 Hz
all frequencies above 1000 Hz
f = 1562.5 Hz
f = 1666.67 Hz

⇒ If each branch of a Delta circuit has impedance 3 Z then each branch of the equivalent Y circuit has impedance.
Z/3
3 Z
3/3 Z
Z/3

⇒ Which of the following ICs has only one NAND gate?
7410
7420
7430
7447

⇒ In practical commercial FM system, channel bandwidth is
150 kHz
100 kHz
88 MHz
108 MHz

⇒ Which of the following parameters is negligible in transmission lines?
R
L
C
G

⇒ RF choke used for suppressing interference in TV is generally
honey comb wound coil
iron core coil
single layer coil
multilayer coil

⇒ Super high frequency means more than 3000 MHz.
TRUE
FALSE

⇒ If sound wave has an intensity of 10 Pa. The dB level is about
1.139 dB
11.39 dB
113.9 dB
1139 dB

⇒ Lower chip area requirements of MOS is advantage in
low power circuits
high power circuits
repetitive operation circuits
large scale integration

⇒ Leak type bias is used in plate modulated class C amplifier to
increase the bandwidth
prevent over modulation
prevent excessive grid current
prevent tuned circuit damping

⇒ Pick the odd-one out
Hartley Oscillator
Colpitt oscillator
Clapp oscillator
Weinbridge oscillator

⇒ Which of the following plot can be directly used to determine β?
V_CE versus i_C for constant I_B
V_BE versus i_B for constant V_CE
V_CB versus i_C for constant I_B
All of the above

⇒ The correct hierarchy of operations for the operators & &, = = , = , * is
& & , = = , = , *
* , = = , & & , =
* , & & , = = , =
= , & & , = = , *

⇒ The circuit in the given figur
half adder
full adder
half subtractor
full subtractor

⇒ Pressing a key on telephone set generates two frequencies. The basis for selection of these frequencies is
the harmonics of one frequency should not be mistaken for the other frequency
the audio input to the handset transmitter should not be mistaken for a key pressing
both (a) and (b)
neither (a) nor (b)

⇒ If both emitter base and collector base junctions of a BJT are forward biased, the transistor is in
active region
saturated region
cut off region
inverse mode

⇒

Match the following:

	List I		List II
A.	Resistance	1.	Current noise
B.	Diode	2.	Partition noise
C.	Triode	3.	Shot noise
D.	p-n junction	4.	Atmospheric noise
		5.	Johnson noise

A-5, B-3, C-2, D-1
A-1, B-2, C-3, D-5
A-3, B-5, C-1, D-2
A-3, B-5, C-2, D-1

⇒ Hall effect is observed in a specimen when it is carrying current and is placed in a magnetic field. The resulting electric field inside the speciment will be in
direction normal to both current and magnetic field
the direction of current
direction antiparallel to magnetic field
an arbitrary direction depend upon conductivity

⇒ An image uses 512 x 512 picture elements. Each of the picture elements can take any of the 8 distinguishable intensity levels. The maximum entropy in the above image will be
2097152 bits
786432 bits
648 bits
144 bits