Question is ⇒ The material of the heating element for a furnace should have, Options are ⇒ (A) lower melting point, (B) higher temperature co-efficient, (C) high specific resistance, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ The material of the heating element for a furnace should have, Options are ⇒ (A) lower melting point, (B) higher temperature co-efficient, (C) high specific resistance, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The material of the heating element for a furnace should have
A.	lower melting point [Wrong Answer]
B.	higher temperature co-efficient [Wrong Answer]
C.	high specific resistance [Correct Answer]
D.	all of the above [Wrong Answer]
View Answer 6 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following methods is used to control temperature in resistance furnaces ?
Variation of resistance
Variation of voltage
Periodical switching on and off of the supply
All of the above methods

⇒ Heat transfer by condition will not occur when
bodies are kept in vacuum
bodies are immersed in water
bodies are exposed to thermal radiations
temperatures of the two bodies are identical

⇒ The temperature inside a furnace is usually measured by which of the following?
Optical pyrometer
Mercury thermometer
Alcohol thermometer
Any of the above

⇒ In electric press, mica is used because it is ____ conductor of heat but/and ____ conductor of electricity.
bad, good
bad, bad
good, bad
good, good

⇒ In direct arc furnace which of the following has high value ?
Current
Voltage
Power factor
All of the above

⇒ The electrode of a direct arc furnace is made of
tungsten
graphite
silver
copper

⇒ The process of heat transfer during the re-entry of satellites and missiles, at very high speeds, into earths atmosphere is known as
ablation
radiation
viscous dissipation
irradiation

⇒ For the transmission of heat from one body to another
temperature of the two bodies must be different
both bodies must be solids
both bodies must be in contact
at least one of the bodies must have some source of heating

⇒ Radiant heating is used for which of the following ?
Annealing of metals
Melting of ferrous metals
Heating of liquids in electric kettle
Drying of paints and varnishes

⇒ Which of the following heating methods has maximum power factor ?
Arc heating
Dielectric heating
Induction heating
Resistance heating

⇒ Direct arc furnaces have which of the following power factors ?
Unity
Low, lagging
Low, leading
Any of the above

⇒ In induction heating ____ is abnormally high.
phase angle
frequency
current
voltage

⇒ Which of the following is an advantage of eddy current heating ?
The amount of heat generated can be controlled accurately
Heat at very high rate can be generated
The area of the surface over which heat is produced can be accurately controlled
All of the above

⇒ ____ is used for heating non-conducting materials.
Eddy current heating
Arc heating
Induction heating
Dielectric heating

⇒ In the indirect resistance heating method, maximum heat-transfer takes place by
radiation
convection
conduction
any of the above

⇒ Which of the following will happen if the thickness of refractory wall of furnace is increased ?
Heat loss through furnace wall will increase
Temperature inside the furnace will fall
Temperature on the outer surface of furnace walls will drop
Energy consumption will increase

⇒ Induction furnaces are employed for which of the following?
Heat treatment of castings
Heating of insulators
Melting aluminium
None of the above

⇒ Which of the following methods of heating is not dependent on the frequency of supply ?
Induction heating
Dielectric heating
Electric resistance heating
All of the above

⇒ Resistance variation method of temperature control is done by connecting resistance elements in
series
parallel
series-parallel connections
star-delta connections

⇒ Radiations from pro,portional to a black body are
T
T²
T³
T⁴

⇒ Which of the following is an advantage of heating by electricity ?
Quicker operation
Higher efficiency
Absence of flue gases
All of the above

⇒ For radiant heating around 2250°C, the heating elements are made of
copper alloy
carbon
tungsten alloy
stainless steel alloy

⇒ The material of the heating element for a furnace should have
lower melting point
higher temperature co-efficient
high specific resistance
all of the above

⇒ Heat is transferred simultaneously by condition, convection and radiation
inside boiler furnaces
during melting of ice
through the surface of the insulted pipe carrying steam
from refrigerator coils to freezer of a refrigerator

⇒ In arc furnace the function of choke is
to stabilize the arc
to improve power factor
to reduce severity of the surge
none of the above

⇒ In an electric room heat convector the method of heating used is
arc heating
resistance heating
induction heating
dielectric heating

⇒ Which of the following insulating materials is suitable for low temperature applications?
Asbestos paper
Diatomaceous earth
80 percent magnesia
Cork

⇒ A perfect black body is one that
transmits all incident radiations
absorbs all incident radiations
reflects all incident radiations
absorbs, reflects and transmits all incident radiations

⇒ Hysteresis loss and eddy current loss are used in
induction heating of steel
dielectric heating
induction heating of brass
resistance heating

⇒ Induction heating takes place in which of the following ?
Insulating materials
Conducting materials which are magnetic
Conducting materials which are non-magnetic
Conducting materials which may or may not be magnetic