Question is ⇒ The material commonly used for air craft gas turbine is, Options are ⇒ (A) stainless steel, (B) high alloy' steel, (C) duralumin, (D) Timken, Haste and Colonel alloys, (E) titanium., Leave your comments or Download question paper.

Question is ⇒ The material commonly used for air craft gas turbine is, Options are ⇒ (A) stainless steel, (B) high alloy' steel, (C) duralumin, (D) Timken, Haste and Colonel alloys, (E) titanium., Leave your comments or Download question paper. Previous question Next question


Q1.	The material commonly used for air craft gas turbine is
A.	stainless steel [Wrong Answer]
B.	high alloy' steel [Wrong Answer]
C.	duralumin [Wrong Answer]
D.	Timken, Haste and Colonel alloys [Correct Answer]
E.	titanium. [Wrong Answer]
View Answer 1 -4 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The criterion of the thermodynamic efficiency for rotary compressor is
isentropic compression
isothermal compression
polytropic compression
any one of the above

⇒ The compressor performance at higher altitude compared to sea level will be
same
higher
lower
dependent on other factors

⇒ The ratio of isentropic work to Euler work is known as
pressure coefficient
work coefficient
polytropic reaction
slip factor

⇒ The fuel consumption in gas turbines is accounted for by
low.er heating value
higher heating value
heating value
higher calorific value

⇒ Which is false statement about advantages of multistage compressor in comparison to single stage compressor
less power requirement
better mechanical balance
less loss of air due to leakage past the cylinder
more effective lubrication

⇒ The volumetric efficiency of a compressor falls roughly as follows for every 5°C increase in atmospheric temperature
0.1%
0.5%
1%
5%

⇒ The closed cycle in gas turbines
provides greater flexibility
provides lesser flexibility
in never used
is used when gas is to be burnt

⇒ The overall isothermal eiffciency of compressor is defined as the ratio of
isothermal h.p. to the BHP of motor
isothermal h.p. to adiabatic h.p.
power to drive compressor to isothermal h.p.
work to compress air isothermally to work for actual compression

⇒ To avoid moisture troubles, the branch connections from compressed air lines should be taken from
top side of main
bottom side of main
left side of main
right side of main

⇒ Out of the following, from where you will prefer to take intake for air compressor
from an air conditioned room maintained at 20°C
from outside atmosphere at 1°C
from coal yard side
from a side where cooling tower is located nearby

⇒ Rotary compressor is best suited for
large quantity of air at high pressure
small quantity of air at high pressure
small quantity of air at low pressure
large quantity of air at low pressure

⇒ A centrifugal compressor works on the principle of
conversion of pressure energy into kinetic energy
conversion of kinetic energy into pres¬sure energy
centripetal action
generating pressure directly

⇒ The compressor efficiency is the
isothermal H.P/indicated H.R
isothermal H.P./shaft H.R
total output/air input
compression work/motor input

⇒ Axial flow compressor resembles
centrifugal pump
reciprocating pump
turbine
sliding vane compressor

⇒ Actual compression curve is
same as isothermal
same as adiabatic
better than isothermal and adiabatic
in between isothermal and adiabatic

⇒ The pressure ratio of an ideal vaned compressor with increase in mass flow rate
increases
decreases
remains constant
first decreases and then increases

⇒ Mining industry usually employs following motive power
A.C. electric motor
compressed air
petrol engine
diesel engine

⇒ The clearance volume of the air compressor is kept minimum because
it allows maximum compression to be achieved
it greatly affects volumetric efficiency
it results in minimum work
it permits isothermal compression

⇒ The combustion efficiency of a gas turbine using perfect combustion chamber is of the order of
50%
75%
85%
90%

⇒ The maximum combustion pressure in gas turbine as compared to I.C. engine is
more
less
same
depends on other factors

⇒ Cylinder clearance in a compressor should be
as large as possible
as small as possible
about 50% of swept volume
about 100% of swept volume

⇒ If infinite number of heaters be used in a gas turbine, then expansion process in turbine approaches
isothermal
isentropic
adiabatic
isochoric

⇒ Standard air is the air at
atmospheric conditions at any specific location
20°C and 1 kg/cm2 and relative humidity 36%
0°C and standard atmospheric conditions
15°C and 1 kg/cm2

⇒ Diffuser in a compressor is used to
increase velocity
make the flow stream-line
convert pressure energy into kinetic energy
convert kinetic energy into pressure energy

⇒ Pick up the wrong statement about advantages of multistage compression
better lubrication is possible advantages of multistage
more loss of air due to leakage past the cylinder
mechanical balance is better
air can be cooled perfectly in between

⇒ The material commonly used for air craft gas turbine is
stainless steel
high alloy' steel
duralumin
Timken, Haste and Colonel alloys

⇒ The hottest point in a gas turbine is
at the base
at the tip
in the center
between ~ to i of the blade height

⇒ The work done per unit mass of air in compression will'be least when n is equal to
1
1.2 ,
1.3
1.4

⇒ Free air is the air at
atmospheric conditions at any specific location
20°C and 1 kg/cm2 and relative humidity of 36%
0°C and standard atmospheric conditions
15°C and 1 kg/cm2

⇒ As the turbine inlet temperature increases, the thermal efficiency of gas turbine for the optimum pressure ratio
increases
decreases
remains same
first increases and then decreases