Question is ⇒ The main beam is a beam which supports, Options are ⇒ (A) Floor construction, (B) Joists, (C) Secondary beam, (D) Both (B) and (C), (E) , Leave your comments or Download question paper.

Question is ⇒ The main beam is a beam which supports, Options are ⇒ (A) Floor construction, (B) Joists, (C) Secondary beam, (D) Both (B) and (C), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The main beam is a beam which supports
A.	Floor construction [Wrong Answer]
B.	Joists [Wrong Answer]
C.	Secondary beam [Wrong Answer]
D.	Both (B) and (C) [Correct Answer]
View Answer 25 -13 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Design of a riveted joint, is based on the assumption:
Load is uniformly distributed among all the rivets
Shear stress on a rivet is uniformly distributed over its gross area
Bearing stress in the rivet is neglected
All the above.

⇒ The thickness of the web of a mild steel plate girder is less than d/200. If only one horizontal stiffener is used, it is placed at.
the neutral axis of the section
2/3rd of the depth of the neutral axis from the compression flange
2/5th of the depth of the neutral axis from the compression flange
2/5th of the height of the neutral axis from tension flange

⇒ The capacity of the smallest pressed steel tank is
1000 litre
1650 litre
1950 litre
2450 litre

⇒ The effective length of a double angle strut with angles placed back to back and connected to both the sides of a gusset plate, by not less than two rivets, is.
0.5 L
0.67 L
0.85 L
L

⇒ Rocker bearings are suitable for span
Less than 8 m
Upto 12 m
12 to 20 m
More than 20 m

⇒ Fillet weld is not used for joining the parts, when the angle between fusion faces is
Greater than 120°
Less than 60°
Both are correct
Both are wrong

⇒ When the length of a tension member is too long.;
a wire rope is used
a rod is used
a bar is used
a single angle is used.

⇒ The external wind pressure acting on a roof depends on
degree of permeability of roof
slope of roof
both (a) and (b)
none of the above

⇒ A fillet weld is known as standard fillet weld if the cross-section of the fillet weld is a triangle of the angle of
45°
60°
30°
75°

⇒ The best arrangement to provide unified behavior in built up steel columns is by
lacing
battening
tie plates
perforated cover plates

⇒ According to IRC recommendations the bridge approaches should be straight for a minimum length of
25 m
30 m
50 m
15 m

⇒ The maximum permissible slenderness ratio of compression member carrying dead and superimposed load, is.
180
200
250
300

⇒ A fillet weld may be termed as.
mitre weld
concave weld
convex weld
all the above.

⇒ Special maintenance of bridges is carried out once in
3 to 6 months
1 to 2 years
2 to 4 years
3 to 5 years

⇒

Poisson's ratio for steel within elastic limit, ranges from.

0.15 to 0.20
0.25 to 0.24
0.25 to 0.33
0.33 to 0.35

⇒ As per IS 800-1984 the minimum pitch of rivets in a row is recommended as diameter of the rivet times
2.0
2.5
3.0
4.0

⇒ A simply supported beam carrying a central load, will be safe in deflection if the ratio of its span to depth, is.
< 19
< 24
> 19
> 24

⇒ The mechanism method of plastic analysis satisfies
equilibrium and mechanism conditions
equilibrium and plastic moment conditions
mechanism and plastic moment conditions
equilibrium condition only

⇒ For steel members not exposed to weather, the thickness of steel should not be less than.
4.5 mm
6 mm
8 mm
10 mm

⇒ The Indian standard code which deals with steel structures, is.
IS : 875
IS : 800
IS : 456
IS : 1893

⇒ Normally, the angle of roof truss with asbestos sheets should not be less than
26'/2°
30°
35°
40°

⇒ Working shear stress on the gross area of a rivet as recommended by Indian Standards, is.
785 kg/cm2
1025 kg/cm2
2360 kg/cm2
none of these.

⇒ If a structure is under fatigue stresses then the welded joints as compared to riveted joints will fail
Earlier
Later
At the same time
Not at all

⇒ The centre to centre distance between any two adjacent supports of a bridge is called
Total span
Gauge
Span
Clear span

⇒ A second horizontal stiffener is always placed at the neutral axis of the girder if the thickness of the web is less than.
d/250 for structural steel
d/225 for high tensile steel
both (c) and (b)
neither (a) nor (b)

⇒ The greatest grip of long rivets shall not exceed
2d
4d
8d
6d

⇒ The effective length of a fillet weld should not be less than
two times the weld size
four times the weld size
six times the weld size
weld size

⇒ A web plate is called unstiffened if the ratio of clear depth to thickness is less than.
35
50
60
85

⇒ Pick up the correct statement from the following:
Loaded columns are supported on column bases
Column bases transmit the column load to the concrete foundation
Column load is spread over a large area on concrete
All the above.

⇒ A compression member consisting of angle sections may be a.
continuous member
discontinuous single angle strut
discontinuous double angle strut
all the above.