Question is ⇒ The instruction <code>MVI A, 20</code> in 8085 means, Options are ⇒ (A) contents of memory location 20 are brought into the accumulator, (B) the value 20 is brought into accumulator, (C) either (a) or (b), (D) neither (a) nor (b), (E) , Leave your comments or Download question paper.

Question is ⇒ The instruction <code>MVI A, 20</code> in 8085 means, Options are ⇒ (A) contents of memory location 20 are brought into the accumulator, (B) the value 20 is brought into accumulator, (C) either (a) or (b), (D) neither (a) nor (b), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The instruction `MVI A, 20` in 8085 means
A.	contents of memory location 20 are brought into the accumulator [Wrong Answer]
B.	the value 20 is brought into accumulator [Correct Answer]
C.	either (a) or (b) [Wrong Answer]
D.	neither (a) nor (b) [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The maximum effective aperture of a microwave antenna which has a directivity of 900, will be
71.619 λ²
716.19 λ²
7161.9 λ²
71619 λ²

⇒ A communication channel disturbed by additive white, Gaussian noise has a bandwidth of 4 kHz and SNR of 15. The highest transmission rate that this channel can support (in k bits/sec) is
16
1.6
3.2
60

⇒ A uniform plane EM wave incident normally on a plane surface of a dielectric material is reflected with a VSWR of 3. What percentage of incident power that is reflected?
0.1
0.25
0.5
0.75

⇒ Which of the following is correct (FDM means Frequency Division Multiplexing and TDM means Time Division Multiplexing)?
FDM requires lower bandwidth but TDM has more noise immunity
FDM has more noise immunity and requires lower bandwidth than TDM
FDM requires channel synchronization while TDM has more noise immunity
FDM requires more multiplexing while TDM requires band pass filter

⇒ The resistivity of intrinsic semiconductors, at room temperature, is of the order of
1 Ω-m
1000 Ω-m
10⁶ Ω-m
10^-3 Ω-m

⇒ A P-N junction diode dynamic conductance is directly proportional to
the applied voltage
the temperature
its current
thermal voltage

⇒ In figure the output V₀
2V₁ + V₂ - 2V₃
2(V₁ + V₂) - V₃
V₁ + V₂ + V₃
V₁ + 2V₂ - V₃

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None

⇒ Which of the following can be operated with positive as well as negative gate voltage?
JFET
Both JFET and MOSFET
MOSFET
Neither JFET nor MOSFET

⇒ For the transport lag G(jω) = e^-jωT, the phase angle
is constant
varies linearly with frequency
varies linearly with low frequencies only
values as per square law

⇒ When atoms are held together by the sharing of valence electrons
each atom becomes free to move
neutrons start shifting
they form a covalent bond
some of the electrons are lost

⇒ The antenna current of an AM transmitter is 8 A. When only the carrier is sent, but it increases to 8.93 A. when the carrier is sinusoidally modulated. The percentage modulation is nearly
0.9
0.8
0.75
0.7

⇒ The main disadvantage of the two-hole directional coupler is
poor directivity
narrow bandwidth
high standing wave ratio
low directional coupling

⇒ ABCD + AB C D =
ABC
ABCD
A B D
ABCD

⇒ TTL is used in electronic calculators.
TRUE
FALSE

⇒ In following circuit, R_B will be if V_CC = 10 V, V_S = 2 V, R_C = 5 kΩ, R_S = 90 kΩ, β = 50, I_CE = 0, V_CEsat = 0
230 K
235 K
240 K
250 K

⇒ In an n-p-n transistor, the majority carriers in the base are
electrons
holes
both holes and electrons
either holes or electrons

⇒ Read cycle is always followed by (during instructions execution)
read cycle
write cycle
delete signal
none of these

⇒

Assertion (A): An ac amplifier uses coupling capacitors at input and output

Reason (R): The capacitive reactance varies inversely with frequency. It is infinite for dc

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒

Assertion (A): In complex frequency s = σ + jω, the terms s and ω are nepar frequency and radin frequency.

Reason (R): If ω = 0, the graph of Ke^st will be a decaying exponential if s <

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Which is correct for a driving point function?
If the real part of a pole or zero is zero, that pole must be simple
If the real part of a pole or zero is zero, that pole or zero must be simple
If the real part of a zero is zero, that pole or zero must be simple
If the real part of a zero is zero that zero must be simple

⇒ A transmitter power of 5 W is increased by 20 dB. The effective radiated power is
5 W
100 W
25 W
500 W

⇒ If e = 10 sin(10⁸ t + 3 sin 10⁴ t) then the deviation is
4.77 kHz
47.7 kHz
477 kHz
4770 kHz

⇒ A voltage V(t) which is a Gaussian ergodic random process with a mean of zero and a variance of 4 volt² is measured by a true rms meter. The reading will be
0
4
2
16

⇒ Signal to noise ratio of microphone is defined as the ratio of output when the sound pressure is __________ to the output in the absence of any sound signal.
0.5 Pa
0.2 Pa
0.1 Pa
0.01 Pa

⇒ At resonance the network function magnitude will be
k/a
k/b
c
k/a + b

⇒ A signal m(t) = 5 cos 2p 100 t frequency modulates a carrier. The resulting FM signal
0.1 kHz
6 kHz
3.2 kHz
100 kHz

⇒ Which of these commutation methods is used in AC-DC converters?
Class A
Class C
Class D
Class F

⇒

Assertion (A): Capacitance of a solid conducting spherical body of radius 'a' is given by 4 pε₀a in free space.

Reason (R): Δ x H = jωεE + J.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Consider the following statements about constants in 8085

The assembler treats 64 H as hexadecimal constant.
The assembler treats 154 as binary constant.
The assembler treats 540 as octal constant.
The assembler treats 138 as decimal constant.

Which of the above are correct?
1, 2 and 3 only
1, 3 and 4 only
1 and 3 only
2 and 4 only