Question is ⇒ The gate-source voltage that reduces the drain current to approximately zero is called, Options are ⇒ (A) gate-source on voltage, (B) gate-source voltage, (C) pinch-off voltage, (D) gate-source cut-off voltage, (E) , Leave your comments or Download question paper.

Question is ⇒ The gate-source voltage that reduces the drain current to approximately zero is called, Options are ⇒ (A) gate-source on voltage, (B) gate-source voltage, (C) pinch-off voltage, (D) gate-source cut-off voltage, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The gate-source voltage that reduces the drain current to approximately zero is called
A.	gate-source on voltage [Wrong Answer]
B.	gate-source voltage [Wrong Answer]
C.	pinch-off voltage [Correct Answer]
D.	gate-source cut-off voltage [Wrong Answer]
View Answer 4 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which one of the following is not necessarily an advantage of the phase cancellation method of obtaining SSB over the filter method?
It is possible to generate SSB at any frequency
SSB with lower audio frequencies present can be generated
Switching from one sideband to other is simpler
There are more balanced modulators; therefore the carrier is suppressed better

⇒ In figure, V reads 45V. Then
10.1 A
13.3 A
16.1 A
19.4 A

⇒ To protect an SCR against high di/dt we connect
a capacitance in series with SCR
a capacitance in parallel with SCR
an inductance in parallel with SCR
an inductance in series with SCR

⇒ The percentage saving in power of 100% modulated suppressed carrier AM signal is
100
75
66.6
50

⇒ A dependent source
may be a current source or voltage source
is neither a current source nor a voltage source
is always a voltage source
is always a current source

⇒

Assertion (A): The turn on time of SCR is about 1 to 4 ms.

Reason (R): The turn off time of SCR is about 10 to 300 ms.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Which one of following is correct condition to check the stability of sysytem in terms of impulse response?
Σ(x(n)) < ∞
Σx(n) < 0
Σx(n) = 0
Σx(n) = ∞

⇒ Single parity check is not reliable in case of
paper tape
magnetic tape
magnetic drum
cores

⇒ Choose the correct option, if b (branch), n (nodes), l (links)
b = n + l - 1
no. of twig = n - 1
b = n - l + 1
b, a

⇒ In 2 out of 5 code, decimal number 8 is
11000
10100
11000
1010

⇒ The antenna most commonly used for TV broadcasting in the UHF band is
turnstile antenna
dipole antenna
yagi antenna
rhombic antenna

⇒ A sinusoidal voltage has peak to peak value of 100 V. The rms value is
50 V
70.7 V
35.35 V
141.41 V

⇒ For a rectified sinusoidal wave clipped at 0.707 its peak value (figure), the average valu
70.7 V
63.7 V
54 V
15 V

⇒ Q of a coil

increases with Q increasing frequency
varies linearly with frequency
increase with increasing frequency because R increases at high frequency
decrease after the peak frequency because R increases at H.F. the correct statements are

A, B
C, D
A, C
B, D

⇒ In a Darlington pair
the emitter of first transistor drives the base of the second
the base of the first transistor drives the emitter of the second
emitters of the two transistors are connected through a resistor
none of the above

⇒ Medium scale integration refers to ICs with
more than 12 but less than 30 gates on the same chip
more than 50 gates on the same chip
more than 20 but less than 100 gates on the same chip
more than 12 but less than 100 gates on the same chip

⇒ Which of the following is not correct for two phase servomotor?
Rotor diameter is small
Applied voltages are seldom balanced
Rotor resistance is low
Torque speed curve is linear

⇒ In a clocked latch, clock drives
R NAND gate
S NAND gate
both R and S NAND gates
either R or S NAND gates

⇒ A diode can have a very high forward resistance.
TRUE
FALSE

⇒ In 8085 microprocessor, even after a Reset operation which of the following interrupts remains enabled?
INTR
RST 5.5
RST 7.5
TRAP

⇒ The initial state of MOD-16 down counter is 011. After 37 clock pulses, the state of the counter will be
1011
110
101
1

⇒ What is the correct sequence of the following step in the fabrication of a monolithic, Bipolar junction transistor?

Emitter diffusion
Base diffusion
Buried layer formation
E pi-layer formation

Select the correct answer using the codes given below:
3, 4, 1, 2
4, 3, 1, 2
3, 4, 2, 1
4, 3, 2, 1

⇒

Assertion (A): Both sodium and ferrous are ferromagnetic.

Reason (R): Both sodium and ferrous have body centred cubic structure.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒

Assertion (A): PC-XT is a personal computer.

Reason (R): PC-XT uses a floppy drive and has a medium sized hard disc.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ An A/D converter uses for reference purposes
DC voltage
a saw tooth generator
set of keys
a flip-flop

⇒ The number of memory locations in which 14 address bits can access is
1024
2048
4096
16384

⇒

Assertion (A): Magnetic susceptibility of copper is -0.5 x 10^-5.

Reason (R): Copper is diamagnetic material.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ As regards ∈₀ and ∈_r (absolute and relative permittivity)
both ∈₀ and ∈_r can be interpreted in terms of atomic properties of medium
only ∈_r can be interpreted in terms of atomic properties of medium
only ∈₀ can be interpreted in terms of atomic properties
∈_r has no physical significance

⇒ In a single phase half wave ac regulator feeding a resistive load, the rms load current
is always positive
may be positive or negative
is always negative
can be even zero

⇒ To evaluate X = (A + B + 1.2) * (A + B - C) the sequence of operation is
+ + + - * =
* + + + - =
+ + - * + =
- + + + * =