Question is ⇒ The forbidden energy gap for silicon is, Options are ⇒ (A) 0.12 eV, (B) 1.12 eV, (C) 0.72 eV, (D) 7.2 eV, (E) , Leave your comments or Download question paper.

Question is ⇒ The forbidden energy gap for silicon is, Options are ⇒ (A) 0.12 eV, (B) 1.12 eV, (C) 0.72 eV, (D) 7.2 eV, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The forbidden energy gap for silicon is
A.	0.12 eV [Wrong Answer]
B.	1.12 eV [Correct Answer]
C.	0.72 eV [Wrong Answer]
D.	7.2 eV [Wrong Answer]
View Answer 4 -4 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If we manage to __________ our natural resources, we would leave a better planet for our children.
uphold
restrain
Cherish
conserve

⇒ As the viscosity of a liquid increases, the relaxation time
remains constant
increases
decreases
first decreases then increases

⇒ The potential of suppressor grid (with respect to cathode) is usually
zero
negative
positive
zero or positive

⇒ Transmitted voltage level is:
11
7.8
7.348 V
none of these

⇒ Which of the following statement is incorrect?
UJT is a 3-terminal diode having two unequally doped regions
A UJT can be triggered by any one of its three terminals
The bi-directional switching characteristics of a diac are symmetrical
As compared to JFETs, MOSFETs generate less noise in high gain amplifiers

⇒ The signal plate of vidicon tube is coated with tin oxide.
TRUE
FALSE

⇒ As regards ferromagnetic Curie temperature Q_f and paramagnetic curie temperature θ
Q_f > θ
θ > Q_f
θ equal to or less than Q_f
θ may be equal to less than or more Q_f

⇒ A lens has a hyperfocal distance of 7.5 m. It is focused at 7.5 m. Then
all objects from 7.5 m to infinity will appear in focus
all objects from 3.75 m to infinity will appear in focus
all objects from 0 to 7.5 m will appear in focus
all objects from 0 to 3.75 m will appear in focus

⇒ Figure shows the V-i characteristics of a material. The material is likely t
copper
carbon
zinc oxide
rubber

⇒ For an RC admittance function Y,
Y(∞) < Y(0)
Y(0) < Y(∞)
Y (∞) may be lesser or greater than Y(0)
Y(∞) = Y(0)

⇒ For a hollow waveguide, the axial current must necessarily be
combination of conduction and displacement current
conduction current only
time varying conduction current and displacement current
displacement current only

⇒ In control systems the word controller includes
error detector and feedback element
feedback element and control elements
error detector and control elements
error detector, control elements and feedback elements

⇒ In auxiliary commutated chopper, the charging and discharging time of capacitor
are constant
depend on load current
may be constant or may depend on load current
none of the above

⇒ In case of stabilized reactance modulator AFC system
phase modulator is converted into frequency modulation by equalizer circuit
the discriminator must have a fast time constant to provide demodulation
the higher discriminator frequency, the better oscillator frequency
the discriminator frequency must be too low, or the system will fail

⇒ In a series LCR circuit the maximum inductor voltage is twice the maximum capacitor voltage however current lags by 30° and drop across the inductance is v_L = 100 sin 377t V. Assuming the resistance being 20 Ω, Find the values of the capacitance and inductance.
235 μF, 61.18 μH
230 μF, 61.18 μH
61.18 μF, 230 μH
None of the above

⇒ If damping ratio is 0.5, the lines joining complex poles with origin are inclined to negative real axis at
± 90°
± 60°
± 45°
± 30°

⇒ In a 4 bit weighted resistor D/A converter, the resistor value corresponding to LSB is 32 kΩ. The resistor value corresponding to MSB will be
32 KΩ
16 KΩ
8 KΩ
4 KΩ

⇒ The scale of hot wire instrument is linear.
TRUE
FALSE

⇒ The most common method for biasing a JFET is
reverse bias
self bias
voltage divider bias
none of the above

⇒ The effect of source inductance in a 3 phase fully controlled bridge converter is to
decrease the output voltage
increase the output voltage
decrease the output voltage and increase the output current
increase the output voltage and decrease the output current

⇒ Find the maximum power that can be delivered to a
0.025 W
2.5 W
2.5 W
0.25 W

⇒ When sources of different frequencies feed a network the only method of solution is superposition theorem.
TRUE
FALSE

⇒ Under ordinary circumstances, impulse noise can be reduced in
FM only
AM only
both AM and FM
none of the above

⇒ To produce p type semiconductor we add
acceptor atoms
donor atoms
pentavalent impurity
trivalent impurity

⇒

Match the following:

	List I		List II
A.	CTFS	1.	Periodic
B.	DTFS	2.	Non-periodic
C.	CTFT
D.	DTFT

A-2, B-1, C-2, D-2
A-2, B-1, C-2, D-1
A-1, B-2, C-2, D-2
A-1, B-2, C-2, D-1

⇒ A radio frequency signal contains the following three frequencie
Push pull amplifier
Wideband amplifier
Audio frequency amplifier
Tuned voltage amplifier

⇒ Which device can detect the presence of both forward and backward waves in a waveguide?
Filter
Detector
Directional coupler
Magic T

⇒ Bipolar signalling uses the following bits
-1, +1
-1, 0, +1
0, 1
-1, 0

⇒ Pirani gauge is used to measure
very low pressure
high pressure
pressure in the range of 1 atmosphere
fluid flow

⇒ A lag compensator is essentially a
low pass filter
high pass filter
band pass filter
either (a) or (b)