Question is ⇒ The following sequence represents autocorrelation of a real valued signal. The energy of real valued sequence is given by __________ x(n) = {1, _, 3, _, 5, _, 7, _, 9, 10, _, 8, _, 6, _, 4, _, 2, Options are ⇒ (A) 2[12 + 22 + 32 + 42 + 52 + 62 + 72 + 82 + 92] + 102, (B) 10, (C) 102, (D) 2[12 + 22 + 32 + 42 + 52 + 62 + 72 + 82 + 92 + 102], (E) , Leave your comments or Download question paper.

Question is ⇒ The following sequence represents autocorrelation of a real valued signal. The energy of real valued sequence is given by __________ x(n) = {1, _, 3, _, 5, _, 7, _, 9, 10, _, 8, _, 6, _, 4, _, 2, Options are ⇒ (A) 2[12 + 22 + 32 + 42 + 52 + 62 + 72 + 82 + 92] + 102, (B) 10, (C) 102, (D) 2[12 + 22 + 32 + 42 + 52 + 62 + 72 + 82 + 92 + 102], (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The following sequence represents autocorrelation of a real valued signal. The energy of real valued sequence is given by __________ x(n) = {1, _, 3, _, 5, _, 7, _, 9, 10, _, 8, _, 6, _, 4, _, 2
A.	2[1² + 2² + 3² + 4² + 5² + 6² + 7² + 8² + 9²] + 10² [Wrong Answer]
B.	10 [Correct Answer]
C.	10² [Wrong Answer]
D.	2[1² + 2² + 3² + 4² + 5² + 6² + 7² + 8² + 9² + 10²] [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): Slotted line is frequently used for microwave measurements.

Reason (R): The unknown impedance is mounted at the end of slotted line.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ For a NAND SR latch of input is the normal resting state of inputs is
S = R = 1
S = 0, R = 1
S = 1, R = 0
S = R = 0

⇒ Consider the following part of a C program float a
2 and 9
2.0 and 9.0
2.0 and 2.0
9.0 and 2.0

⇒ If all the LEDs in a seven segment display are turned on, the number displayed is
1
3
0
8

⇒ In a series RLC high Q circuit the current peaks at a frequency.
equal to the resonant frequency
greater than the resonant frequency
less than the resonant frequency
none

⇒ Consider the following statements

In 8085 address and data buses are multiplexed.
In Z 80 address and data buses are multiplexed
In Z 80 address and data buses are not multiplexed.
Z 80 has 16 bit address bus and 8 bit data bus.

Which of the above statements are correct?
1 and 2 only
1, 3 and 4 only
1, 2 and 4 only
2 and 4 only

⇒ Find resistance R_B to bring transistor to threshold of saturation V_CB = 0, V_BE = 0.7 V, a =
1.5 kΩ
15 kΩ
10 kΩ
1 kΩ

⇒ If V = 20 + j20, then log_e(A) A is
3.342 + j 45
28.28 ∠45°
400 ∠45°
3.342 + j 0.785

⇒ A bit synchronizer regenerates at the receiver a clock waveform which is
synchronous with original clock waveform
out of phase by 180° with original clock waveform
out of phase by 90° with the original clock waveform
none of the above

⇒ A signal x₁(t) and x₂(t) constitute the real and imaginary parts respectively of a complex valued signal x(t). What form of waveform does x(t) possess?
Real symmetric
Complex symmetric
Asymmetric
Conjugate symmetric

⇒ For the differential equation (D³ - D² + D -1) [y(t)] = 0 the root of auxiliary equation
-j, j, 1
-j, j, 2
1, 2, j
1, 2, -j

⇒

Assertion (A): Microprocessor 8085 has on-chip oscillator with inbuilt crystal.

Reason (R): For frequency stability crystal oscillator is preferred.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ A 4 bit modulo 16 ripple counter uses JK flip-flops. If the propagation delay of each FF is 50 ns. The max. clock frequency that can be used is equal to
20 MHz
10 MHz
5 MHz
4 MHz

⇒ As compared to a full wave diode rectifier circuit using centre tapped transformer, the bridge diode rectifier circuit has the main advantage of
higher current carrying capacity
higher efficiency
lower ripple factor
lower PIV

⇒ Two similar mutually coupled coils have a total inductance of 900 mH and coefficient of coupling 0.5. The self inductance of each coils is
300 mH
150 mH
75 mH
50 mH

⇒ Ferrite have
low copper loss
low eddy current loss
low resistivity
higher specific gravity compared to iron

⇒ Distances near the skip distance should be used for sky-wave propagation
to avoid the Faraday effect
to avoid tilting
to prevent sky-wave and upper ray interference
so as to exceed the critical frequency

⇒ In figure the total inductance of the circui
L₁ + L₂
L₁ + L₂ - M
L₁ + L₂ - 2M
L₁ + L₂ + M

⇒ No load d.c. output will be least in case of
half wave rectifier
full wave rectifier
bridge rectifier
three phase full wave rectifier

⇒ The relative permittivity of the ionosphere at ratio frequencies is
> 1
< 1
1
≥ 1

⇒ A 4 bit ripple counter uses flip flops with propagation delay of 50 ns each. The maximum clock frequency which can be used is
5 MHz
10 MHz
20 MHz
25 MHz

⇒ In a network
the number of tree branches is always less than the number of links
the number of tree branches is always more than the number of links
the number of tree branches and links are always equal
the number of tree branches has no relation with the number of links

⇒ Charge needed within a unit sphere centred at the origin for producing a potential fie
12 p_c
60 p_c
120 p_c
180 p_c

⇒ The function A e^st where s = s + jω represents
A phasor whose magnitude changes with time
A phasor whose frequency is ω
A phasor rotating in counterclockwise direction at angular frequency ω and whose magnitude increases with t
A phasor rotating in clockwise direction at angular frequency ω and whose magnitude increases with t

⇒ For high frequency response of a transistor amplifier, suitable model to use is
Kelvin network
Lattice network
Hybrid p
T-network

⇒ Which of the following devices has a silicon dioxide layer?
NPN transistor
Tunnel diode
JFET
MOSFET

⇒ The FM broadcast band is from
550 to 1600 kHz
88 to 108 kHz
88 to 108 MHz
1600 kHz to 59.75 MHz

⇒ In case of surface waves the field strength at a point is directly proportional to
antenna height
wave frequency
current of the antenna
distance of the point from the antenna

⇒ When R and L are connected in parallel, R > |Z|.
TRUE
FALSE

⇒ A second order system will have
all resistances
resistances and inductances
resistances, inductance and capacitances
either (b) or (c)