Question is ⇒ The following components are used to measure power output of a 2 kW TWT amplifier <ol style="list-style-type: decimal; padding-bottom:10px;"><li style="padding-top:10px;">TWT</li><li style="padding-top:10px;">Low pass/High pass filter</li><li style="padding-top:10px;">Low power 20 dB attenuator</li><li style="padding-top:10px;">40 dB directional coupler with matched load</li><li style="padding-top:10px;">Power meter.</li></ol> The correct sequence of connections of these components is:, Options are ⇒ (A) 1, 4, 2, 3, 5, (B) 1, 3, 4, 2, 5, (C) 1, 2, 4, 3, 5, (D) 1, 4, 3, 2, 5, (E) , Leave your comments or Download question paper.

Question is ⇒ The following components are used to measure power output of a 2 kW TWT amplifier <ol style="list-style-type: decimal; padding-bottom:10px;"><li style="padding-top:10px;">TWT</li><li style="padding-top:10px;">Low pass/High pass filter</li><li style="padding-top:10px;">Low power 20 dB attenuator</li><li style="padding-top:10px;">40 dB directional coupler with matched load</li><li style="padding-top:10px;">Power meter.</li></ol> The correct sequence of connections of these components is:, Options are ⇒ (A) 1, 4, 2, 3, 5, (B) 1, 3, 4, 2, 5, (C) 1, 2, 4, 3, 5, (D) 1, 4, 3, 2, 5, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The following components are used to measure power output of a 2 kW TWT amplifier TWT Low pass/High pass filter Low power 20 dB attenuator 40 dB directional coupler with matched load Power meter. The correct sequence of connections of these components is:
A.	1, 4, 2, 3, 5 [Wrong Answer]
B.	1, 3, 4, 2, 5 [Correct Answer]
C.	1, 2, 4, 3, 5 [Wrong Answer]
D.	1, 4, 3, 2, 5 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The pole zero plot of the given figure is
non-minimum phase function
minimum phase function
all pass function
none of the above

⇒

Assertion (A): The resistance of a copper specimen changes by about 22% when temperature is increased from room temperature to 700°C.

Reason (R): The physical properties of a material are determined mostly by the extent of impurities.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ The expression Y (A, B, C) = ∑m (1, 3, 5, 6) is to realized using a multiplexer. Then
use 8 : 1 multiplexer and ground input lines 1, 3, 5, 6
use 8 : 1 multiplexer and ground input lines 0, 2, 4, 7
use 8 : 1 multiplexer and ground input lines 0, 1, 2, 3
use 8 : 1 multiplexer and ground input lines 4, 5, 6, 7

⇒ The equivalent inductance seen at terminals A -
14 H
20 H
10 H
4 H

⇒ In figure, the current after a long time after closing of switc
0.0416666666666667
0.0833333333333333
0
infinity

⇒ The radix of a hexadecimal system is
2
3
8
16

⇒ The gain margin of first and second order systems is infinite.
TRUE
FALSE

⇒ In a bridge inverter with single pulse width modulation
the output frequency is equal to frequency of reference signal
the output frequency is equal to frequency of control signal
either (a) or (b)
neither (a) nor (b)

⇒ When a constant voltage source and constant current source are in series, the current source is ineffective.
TRUE
FALSE

⇒ A standard waveguide W R90 has inside wall dimensions of a = 2.286 cm and b = 1.016 cm. What is the cut-off wavelength for TE₀₁ mode?
4.572 cm
2.286 cm
2.032 cm
1.857 cm

⇒ In op-amp integrating amplifier the input is feed to
inverting input
non-inverting input
both inverting and non-inverting input
either inverting or non-inverting input

⇒ In the circuit shown in the given figure the diode states at the extremely large negative values of the input voltage v_i a
D₁ off, D₂ off
D₁ on, D₂ off
D₁ off, D₂ on
D₁ on, D₁ on, D₂ on

⇒ The time constant of the circuit in figur
RC
2 RC
3 RC
5 RC

⇒ The speed transducer using a drag cup rotor has the main advantage of
very high accuracy
low energy requirement
cheap construction
all of the above

⇒ The total power radiated from an antenna system is determined by imagining that the antenna is at the centre of a very large
sphere
rectangle
square
ellipse

⇒ The h parameter equivalent circuit of BJT has one voltage source and one current source.
TRUE
FALSE

⇒ The circuit of the given figure
full adder
full subtractor
shift register
decade counter

⇒ The circuit shown in figure
low pass filter
high pass filter
band pass filter
band stop filter

⇒ The total area under the probability distribution curve is
1
0
depend upon curve equation
∞

⇒ In high power radars, which of the following are used for switching?
Power diode
Power BJT
Power MOSFET
Thyristor

⇒ A system has high gain and phase margin. The system is
very stable
sluggish
very stable and sluggish
oscillatory

⇒ When a magnetic circuit is compared with an electric circuit, the equivalent of the magnetic flux is
the conductivity of the lines
the voltage of the source
the current in the lines
the conductance of the load

⇒ The emitter coupled pair of BJT's gives a linear transfer relation between the differential output voltage and the differential input voltage V_id only when the magnitude of V_id is less a times the thermal voltage, where a is
4
3
2
1

⇒ In a transistor leakage current mainly depends on
doping of base
size of emitter
rating of transistor
temperature

⇒ Consider the following:

A TV receiver antenna should pick up the TV signal and develop maximum voltage from the available strength of signal
It should reject unwanted signals
It should not suffer from co-channel interference
It should have a very narrowband

The correct statements are
1 and 2 only
1, 2 and 3 only
1, 2, 3, 4
2, 3 only

⇒

Match the following:

	List I (Operation in Basic)		List II (Priority)
A.	Exponentiation	1.	1
B.	Multiplication and division	2.	2
C.	Addition and subtraction	3.	3
D.	Expression within parenthesis	4.	4

A-1, B-2, C-3, D-4
A-2, B-3, C-1, D-4
A-4, B-3, C-2, D-1
A-2, B-3, C-4, D-1

⇒ Which of the following codes is based on BCD format?
EBCDIC
ASCII
Hollerith
both (a) and (b)

⇒ The static electric field in a conductor is
zero
unity
infinity
none of the above

⇒ The total bandwidth needed for an AM signal at 55.25 MHz with 0.5 MHz video modulation is
0.25 MHz
0.5 MHz
1 MHz
10 MHz

⇒ When load is coupled to class A amplifier through transformer, efficiency decreases.
TRUE
FALSE