Question is ⇒ The electrical requirement on wall thickness of rectangular wave guide is, Options are ⇒ (A) wall thickness is more than skin depth, (B) wall thickness is less than skin depth, (C) wall thickness is equal to skin depth, (D) either (b) or (c), (E) , Leave your comments or Download question paper.

Question is ⇒ The electrical requirement on wall thickness of rectangular wave guide is, Options are ⇒ (A) wall thickness is more than skin depth, (B) wall thickness is less than skin depth, (C) wall thickness is equal to skin depth, (D) either (b) or (c), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The electrical requirement on wall thickness of rectangular wave guide is
A.	wall thickness is more than skin depth [Correct Answer]
B.	wall thickness is less than skin depth [Wrong Answer]
C.	wall thickness is equal to skin depth [Wrong Answer]
D.	either (b) or (c) [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If V = 100 ∠ 16°, the (V) is
10 ∠ 32°
10 ∠ 8°
10 ∠ 16°
10 ∠ 4°

⇒ Which of the following is also called Non volatile RAM?
Shadow RAM
UVEPROM
EEPROM
Both (b) and (c)

⇒ In Z_RC (s) = constant at s = 0, the last element in first Foster cauer realization is
R
C
R and C in series
R and C in parallel

⇒ The number of accumulators in 6800 are
2
3
1
4

⇒ The resistance of the aluminium conductor (r = 2.83 x 10^-8 Ωm) in figur
0.001 Ω
less than 0.001 Ω
more than 0.001 Ω
more than 0.002 Ω

⇒ In a ripple counter,
whenever a flip flop sets to 1, the next higher FF toggles
whenever a flip flop sets to 0, the next higher FF remains unchanged
whenever a flip flop sets to 1, the next higher FF faces race condition
whenever a flip flop sets to 0, the next higher FF faces race condition

⇒ In which of the following devices can the operation be visualised in terms of a series feedback loops?
TWT
Reflex klystron
Klystron amplifier
Backward wave oscillator

⇒ A 4 bit DAC gives an output of 4.5 V for input of 1001. If input is 0110, the output is
1.5 V
2.0 V
3.0 V
4.5 V

⇒ A 10 MHz square wave clocks 5 bit ripple counter. The frequency of the 3rd FF output is
2 MHz
1.25 MHz
50 MHz
615 kHz

⇒ In the case of the circuit shown in the figure, the collector current I_C will be, if β = 100, V_BE = 0.7 V, I_CO = 0.1 βA at 20&d
2.26 mA
1.85 mA
0.357 mA
0.185 mA

⇒ A 1 MHz sinusoidal carrier is amplitude modulated by a symmetrical square wave of period 100 μ sec. Which of the following frequencies will not be in the modulated signal?
990 kHz
1010 kHz
1020 kHz
1030 kHz

⇒ In a JFET
drain current is very nearly equal to source current
drain current is much less than source current
drain current may be equal to or less than source current
drain current may be even more than source current

⇒ The intermediate frequency of a superheterodyne receiver is 450 kHz. If it is tuned to 1200 kHz, the image frequency will be
750 kHz
900 kHz
1600 kHz
2100 kHz

⇒ Which one is a non-causal system?
y(n) = x(2n)
y(n) = x(n/2)
y(n) = x(n/2) + x(n)
all

⇒ The received signal frequency at any time of a super-heterodyne receiver having IF = 456 kHz is 1 MHz. The corresponding image signal is
within the medium band
outside the medium band
depend upon modulation index
depends on Modulating frequency

⇒ Which of the following is high frequency transmission line?
An impedance transformer
Frequency compensator
Flying resistor
None of the above

⇒ Which 8085 instruction causes exchange of contents of stack pointer with the contents of H L register pair?
XTHL
PCHL
LHLD
MVIA

⇒ The effect of a finite gain of operational amplifier used in an integrator is that
it would not integrator
slope of the O/P will varied with time
final value of the O/P
there will be instability in the cirucuit

⇒ For a D/A converter, inputs and outputs are given. The output corresponding to digital input 01
2.0 V
2.5 V
3.0 V
4.0 V

⇒

Assertion (A): Tie set schedule is used in nodal analysis.

Reason (R): Loop currents are fictitious quantities.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ The average load current supplied by a thyristor depends on
firing angle
firing frequency
magnitude of gate current
all of the above

⇒ IF amplifiers for radio receivers are often tuned to
456 Hz
456 kHz
3456 MHz
456 GHz

⇒ If the circumference of a spherical target is between 1 to 10 wavelength in a radar system, the situation is called
resonance region
Rayleigh region
optical region
binomial region

⇒ The capacitor filter provides poor voltage regulation because
the increase in ripple with load current causes a decrease in average voltage
the increase in ripple with load current causes a increase in average voltage
filter promotes ripple at peak voltage
none of the above

⇒ For the system of the given figure, the closed loop poles ar
0 and -4
-2 ± j6
2 ± j6
-3 ± j8

⇒ At any point on the v-i characteristics of a semiconductor diode, the slope of v-i characteristics is called
resistance of diode
conductance of diode
incremental resistance of diode
incremental conductance of diode

⇒ Consider the following statements

An assembler is a program having assembly language program as input and machine language program as output.
A macro assembler is an assembler with additional macro facilities.
A cross assembler for a μP X is an assembler which executes on source microcomputer with a different CPU than X bit generates code for X.
Assemblers generally do not provide macro facilities.

Of the above statement
All are correct
only 1, 2, 3 are correct
only 1, 2, 4 are correct
only 1, 3, 4 are correct

⇒ How much r.m.s. current does a 300 W, 200 V bulb take from the 200V, 50 Hz power line?
0.5 A
1.5 A
0.0833333333333333
0.125

⇒ Consider the following statements:

With increase in temperature Fermi-level tries to come in between the energy gap exactly at middle
Mobility of electron in GaAs is very high compared to mobility of hole
In LED, the light energy radiated due to recombination with the aid of traps.

Which of these statements are true?
1 and 2
1, 2 and 3
2 and 3
1 and 3

⇒ A clipper
adds a dc component to the input signal
removes signal voltages above or below a specified value
both (a) and (b)
either (a) or (b)