Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The double energy transient occur in the |

A. | Purely inductive circuit [Wrong Answer] |

B. | R-L circuit [Wrong Answer] |

C. | R-C circuit [Wrong Answer] |

D. | R-L-C circuit [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A heater is rated as 230 V, 10 KW, AC. The value 230 V refers t

Average voltage

r.m.s. voltage

Peak voltage

None of these

⇒ Which of the following is not a non-linear element ?

Transistor

Heater coil

Diode

Electric arc with unlike electrodes

⇒ Capacitive reactance is more when

Capacitances is less and frequency of supply is less

Capacitance is less and frequency of supply is more

Capacitance is more and frequency of supply is less

Capacitance is more and frequency of supply is more

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?

Square wave

Half wave rectified sine wave

Triangular wave

Sine wave

⇒ In a series resonant circuit, the impedance of the circuit is

Maximum

Minimum

Zero

Infinite

⇒ The dual of a loop is

Twig

Node pair

Mesh

Tree

⇒ A parallel resonant circuit can be used

As a high impedance

To reject a small band of frequencies

Both (A) and (B)

To amplify certain frequencies

⇒ All the rules and laws of D.C. circuit also supply to A.C. circuit containing

Capacitance only

Inductance only

Resistance only

All above

⇒ What inductance will give the same reactance as a capacitor of 2 µF when both are at 50 Hz?

5 H

10 H

15 H

20 H

⇒ Form factor is the ratio of

Average value/r.m.s. value

Average value/peak value

r.m.s. value/average value

r.m.s. value/peak value

⇒ In a circuit containing R, L and C, power loss can take place

C only

L only

R only

All of the above

⇒ The peak value of a sine wave is 200 V. Its average value is

127.4V

141.4V

282.8V

200 V

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in

Parallel

Series

Either (A) or (B)

None

⇒ The shunt element in a band pass filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ The series element of a band stop filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ A network is said to be non-linear if it does not satisfy

Homogeneity condition

Superposition condition

Both (A) and (B)

Associative condition

⇒ In a pure resistive circuit

Current lags behind the voltage by 90°

Current leads the voltage by 90°

Current can lead or lag the voltage by 90°

Current is in phase with the voltage

⇒ In A.C. circuit laminated iron is invariably used in order to

Reduce eddy current loss

Increase heat radiation

Make assembly cheap and easier

Reduce circuit permeability

⇒ The value of operator j2 is equal to

Zero

+1

-1

√-1

⇒ The negative maximum of a cosine wave occurs at

30

45

90

180

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates

Low efficiency

High power factor

Unity power factor

Maximum Load current

⇒ Poor power factor results in all of the following EXCEPT.

Overloading of transformers

Overloading of altemators

Reduction in power losses

Reduction in load handling capacity of electrical system

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is

360°

180°

90°

0°

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is

70.7 A

141.4A

150A

282.8 A

⇒ Ohm is the unit of all of the following except

Inductive reactance

Capacitive reactance

Resistance

Capacitance

⇒ The frequency of domestic power supply in India is

200 Hz

100 Hz

60 Hz

50 Hz

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage

180°

90°

60°

0°

⇒ Which of the following circuit component opposes the change in the circuit voltage

Inductance

Capacitance

Conductance

Resistance

⇒ Power factor of the following circuit will be zero

Resistance

Inductance

Capacitance

Both (B) and (C)