Question is ⇒ The dominant mode in a rectangular wave-guide is, Options are ⇒ (A) TE01, (B) TM01, (C) TE10, (D) TM11, (E) , Leave your comments or Download question paper.

Question is ⇒ The dominant mode in a rectangular wave-guide is, Options are ⇒ (A) TE01, (B) TM01, (C) TE10, (D) TM11, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The dominant mode in a rectangular wave-guide is
A.	TE₀₁ [Wrong Answer]
B.	TM₀₁ [Wrong Answer]
C.	TE₁₀ [Correct Answer]
D.	TM₁₁ [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A first-order system has a time constant t. For unit ramp input, the steady state error is
t²
t
t
1/t

⇒ In TE and TM modes of rectangular waveguides having propagation in z direction
E_z and H_z are both zero
In TE mode E_z is zero and in TM mode H_z is zero
In TE mode H_z is zero and in TM mode E_z is zero
In both TE and TM modes both E_z and H_z are non-zero

⇒ Which of the following statements is/are true for a good conductor of electricity?

Its conductivity decreases with increasing temperature.
Number of free electrons is around 10²⁸ m^-3.
Its conductivity decreases with addition of impurities.
It is a good conductor of heat also.

1, 2, 3 and 4
1 only
2 and 3 only
3 and 4 only

⇒ If number of information bits is 11, the number of parity bits in Hamming code is
5
4
3
2

⇒ A hexadecimal odometer displays F52F. The next reading will be
E 52 F
E 52 E
E 53 F
F 53 O

⇒ Due to the formation of Schottky defects the density of the crystal
increases slightly
increases appreciably
decreases slightly
decreases appreciably

⇒ In the given figure
A
B
A + B + C
ABC

⇒ A 3 stage Johnson counter shown in figure is clocked at a constant frequency of f_c from the starting state of Q₀ Q₁ Q₂ = 101. The frequency of output Q₀ Q₁ Q₂ wil
f_c/2
f_c/3
f_c/6
f_c/8

⇒ The gate-source voltage that reduces the drain current to approximately zero is called
gate-source on voltage
gate-source voltage
pinch-off voltage
gate-source cut-off voltage

⇒ The function shown in the fig
impulse function
signum function
unit step function
none of the above

⇒ The output Y of the circuit shown in the figur
(A + B) C + DE
AB + C(D + E)
(A + B) C + D + E
(AB + C) . DE

⇒ A vacant electronic state moves in the same direction as would a positive charge carrier.
TRUE
FALSE

⇒ Find Y in the circuit bel
f₂
f₂
0
∑(0, 1, 2, 3, 5, 6, 9)

⇒ The resistance of a metallic wire would
increase as the operating frequency increase
decrease as the operating frequency increase
remain unaffected on increasing the operating frequency
first increase then decrease

⇒ A short vertical grounded antenna is required to radiate at 1 MHz. The effective height of the antenna is 302 m. The calculated value of radiation resistance is
1.58 Ω
158 Ω
15.8 Ω
none

⇒ "Micro-programming" is a technique
for programming the microprocessors
for writing small programs efficiently
for programming the control steps of a computer
for programming output/input

⇒ A diode detector load consists of 0.01 μF capacitor in parallel with a 5 k ohms resistor. The maximum depth of modulation without diagonal clipping at modulating frequency of 1000 Hz and 10 kHz is
0.76, 0.24
0.95, 0.3
0.24, 076
0.3, 0.95

⇒ A computer program is used to read M and print the sum 2 + 4 + 6 + 8 +.........+ 2M. If M = 9 , the print out will show the number
9
18
90
100

⇒ In the circuit of figure the current through C at t = &infin
0.166666666666667
2.5 A
3.1 A
0

⇒

Assertion (A): An instruction cycle consists of fetch and execute cycles.

Reason (R): Fetch cycle has one machine cycle but execute cycle may have one or more machine cycles depending on length of instruction.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒

Assertion (A): A multiplexer can be used for data routing.

Reason (R): A multiplexer has one input and many outputs.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In a CRO, the time base signal is applied to
X plates
Y plates
either X or Y plates
alternately X and Y plates

⇒ The ripple factor for a bridge rectifier is
0.406
1.21
1.11
2.22

⇒ When a large number of atoms are brought together to form a crystal
the energy levels of inner shell electrons are affected appreciably by the presence of other neighbouring atoms.
The energy levels of outer shell electrons are affected appreciably by the presence of other neighbouring atoms.
the energy levels of both inner and outer shell electrons are affected appreciably by the presence of other neighbouring atoms.
none of the above.

⇒ The resistance of resistance strain gauge is about
5 Ω
50 Ω
120 Ω
0.5 Ω

⇒ In a JK flip-flop, J is connected to Q and K is connected to Q outputs. The JK FF converts into a
RS FF
D FF
T FF
Clocked RS FF

⇒ Consider the following expression for the driving point imped
2 and 4
1 and 3
1 and 4
2 and 3

⇒ Which camera tube has highest sensitivity and very wide spectral response?
Vidicon
Plumbicon
New vicon
Saticon

⇒ The h parameter equivalent circuit of BJT has one voltage source and one current source.
TRUE
FALSE

⇒ The ASCII code is for information interchange by a binary code for
alphabet only
number only
alpha-numeric and other common symbols
none of these