Question is ⇒ The distance of poles from origin depends on, Options are ⇒ (A) undamped natural frequency, (B) damping ratio, (C) both (a) and (b), (D) neither (a) nor (b), (E) , Leave your comments or Download question paper.

Question is ⇒ The distance of poles from origin depends on, Options are ⇒ (A) undamped natural frequency, (B) damping ratio, (C) both (a) and (b), (D) neither (a) nor (b), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The distance of poles from origin depends on
A.	undamped natural frequency [Correct Answer]
B.	damping ratio [Wrong Answer]
C.	both (a) and (b) [Wrong Answer]
D.	neither (a) nor (b) [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ What does the instruction 'PCHL' in 8085 do?
Load the program counter with contents of register pair H L
Double the contents of register pair H L
Shift the contents of register pair H L by one bit to the right
Shift the contents of register pair H L by one bit to left

⇒ In a good voltage amplifier, its input impedance
must be high compared to the resistance of the source
must be low compared to the resistance of the source
must be equal to the resistance of the source
must be half the resistance of the source

⇒ When a series RL circuit is switched on to a dc voltage, the rate of change of current is maximum at t = 0.
TRUE
FALSE

⇒ A (75 - j 50) Ω load is connected to a coaxial line of Z₀ = 75 Ω at 10 GHz. The best method of matching consists of using
a capacitance at some specific distance from load
a short circuited stub at some specific distance from load
an inductance at load
a short circuited stub at load

⇒ The gate-source voltage that reduces the drain current to approximately zero is called
gate-source on voltage
gate-source voltage
pinch-off voltage
gate-source cut-off voltage

⇒ A 2 bit BCD D/A converter is a weighted resistor type with E_R = 1V, R = 1 MΩ and R_f = 10KΩ then Resolution in percent and volt is __________ .
1%, 1 mv
10%, 10 mv
10%, 1 mv
1%, 10 mv

⇒ VTM stands for voltage tunable magnetron.
TRUE
FALSE

⇒

Assertion (A): Temperature control of the passenger compartment of car uses both feed forward and feedback controls.

Reason (R): Feed forward control gives corrective action before the disturbance affects the output and feedback control applies corrective action after output changes.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ In free space, line of sight propagation case, the transmission losses between transmitter and receiver increase with frequency (f) as
f
f²
f⁴
f^1/2

⇒ In the given fi
42737
42739
2
1

⇒ In an LC immittance H (s)
the slope of dH (jω)/dω is always negative
the slope of dH (jω)/dω is always positive
the slope of dH (jω)/dω may be positive or negative
the slope of dH (jω)/dω is constant

⇒ If 1.5% of the output of an amplifier is feedback positively to the input, the minimum gain required of the amplifier for oscillations to occur, is
16.6
44.4
66.6
75

⇒ The most commonly used transistor amplifier circuit is
CB
CC
CE
CE or CC

⇒ (1001-10) is equal to
7
(8)₈
(7)₄
(8)₄

⇒ In a lead acid cell the density of the acid gives an indication of
the level of the acid
the eventual damages caused to the plates
the charge of the battery
the e.m.f. of the battery

⇒ For a single phase half wave converter feeding a resistive load, the firing angle a. The waveshape in below figure is
output voltage
input voltage
voltage drop across thyristor
none of the above

⇒ The effective electrical length of an antenna is __________ its physical length
greater than
equal to
less than
none of the above

⇒ The inductance of a single layer solenoid of 10 turns is 5 μH. Which one of the following is the correct value of inductance when the number of turns is 20 and the length is doubled.
10 μH
20 μH
40 μH
5 μH

⇒ Equipment using BCD numbers
pocket calculators
electronic counter
digital voltmeters
all of the above

⇒ If a complex voltage wave is applied to a pure inductance, the resulting current wave is much smoother than the voltage wave.
TRUE
FALSE

⇒ A 1 ms pulse can be converted into a 10 ms pulse by using which one of the following
An astable multivibrator
Stable multivibrator
A bistable multivibrator
A J-K flip-flop

⇒ In the spectrum of a FM wave
the carrier frequency cannot disappear
the carrier frequency disappears when the modulation index is large
the amplitude of any sideband depends on the modulation index
the total number of sidebands depends on the modulation index

⇒ For the NMOS gate in the given figure,
ABCDE
(AB + C) (D + E)
A(B + C) + DE
A + B C + DE

⇒ In a junction transistor, the collector cut-off current 'I_CB0' reduces considerably by doping the
emitter with high level of impurity
emitter with low level of impurity
collector with high level of impurity
collector with low level of impurity

⇒ How many roots with positive real parts do the equation s³ + s² - s + 1 = 0 have?
Zero
One
Two
Three

⇒ With the switch in STOP position, Y will be equa
0
1
CLK
none of these

⇒ The carrier mobility in a semiconductor is 0.4 m²/Vs. Its diffusion constant at 300k will be (in m²/s).
0.43
0.16
0.04
0.01

⇒ In the forward blocking region of a silicon, controlled rectifier, the SCR is
in the off-state
in the ON state
reverse biased
at the point of breakdown

⇒

Assertion (A): In intrinsic semiconductors, the charge concentration increases with temperature.

Reason (R): At higher temperatures, the forbidden energy gap in semiconductors is lower.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The system with given pole-zero diagram is _______
Causal
Anti-causal
Both sided
Cannot be determined