Question is ⇒ The distance between steps for measuring down hill to obtain better accuracy., Options are ⇒ (A) decreases with decrease of slope, (B) increases with increase of slope, (C) decreases with increase of slope, (D) decreases with decrease of weight of the chain., (E) , Leave your comments or Download question paper.

Question is ⇒ The distance between steps for measuring down hill to obtain better accuracy., Options are ⇒ (A) decreases with decrease of slope, (B) increases with increase of slope, (C) decreases with increase of slope, (D) decreases with decrease of weight of the chain., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The distance between steps for measuring down hill to obtain better accuracy.
A.	decreases with decrease of slope [Wrong Answer]
B.	increases with increase of slope [Wrong Answer]
C.	decreases with increase of slope [Correct Answer]
D.	decreases with decrease of weight of the chain. [Wrong Answer]
View Answer 29 -6 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If the horizontal distance between the staff point and the point of observation is d, then the error due to curvature of earth is proportional to
d
1/d
d2
1/d2

⇒ If a tripod settles in the interval that elapses between taking a back sight reading and the following foresight reading, then the elevation of turning point will
increase
decrease
not change
either 'a' or 'b'

⇒ The conventional sign shown in below figure represents a

bridge carrying railway below road
bridge carrying road below railway
bridge carrying road and railway at the same level
a level crossing.

⇒ The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is.
3.290 m
3.300 m
3.275 m
2.790 m

⇒ From any point on the surface with a given inclination.
only one contour gradient is possible
two contour gradients are possible
indefinite contour gradients are possible
all the above.

⇒ An offset more than 15m in length is known as
Long offset
Short offset
Oblique offset
Right-angled offset

⇒ Whole circle bearing of a line is preferred to a quadrantal bearing merely because.
bearing is not completely specified by an angle
bearing is completely specified by an angle
Sign of the correction of magnetic declination is different in different quadrants
its trigonometrical values may be extracted from ordinary tables easily.

⇒ With the rise of temperature, the sensitivity of a bubble tube
decreases
increases
remains unaffected
none of the above

⇒ In levelling operation.
when the instrument is being shifted, the staff must not be moved
when the staff is being carried forward, the instrument must remain stationary
both (a) and (b)
neither (a) nor (b).

⇒ In a plane table survey the method used for locating details is
Resection
Resection
Intersection
(A) or (B) above

⇒ A staff reading taken on a bench mark or change point is known as
Back siLT,ht
Fore sight
Intermediate sight
None of the above

⇒ In a theodolite.
the telescope axis is perpendicular to transit axis
the axis of rotation is perpendicular to transit axis
the telescope axis, the transit axis and the rotation axis pass through the centre of theodolite
all the above.

⇒ If L is in kilometres, the curvature correction is.
58.2 L2 mm
64.8 L2 mm
74.8 L2 mm
78.4 L2 mm.

⇒ In plane table survey, the method used for locating plane table station is
Traversina
Resection
Radiation
(A) or (B) above

⇒ The angle between the prolongation of the preceding line and the forward line of a traverse is called
deflection angle
included angle
direct angle
none of the above

⇒ Tadia techeometry was discovered by James Watt in the year.
1670
1770
1870
1900.

⇒ The rise and fall method
is less.accurate than height of instrument method
is not suitable for levelling with tilting levels
provides a check on the reduction of intermediate point levels
quicker and less tedious for large number of intermediate sights

⇒ If the rate of gain of radial acceleration is 0.3 m per sec³ and full centrifugal ratio is developed. On the curve the ratio of the length of the transition curve of same radius on road and railway, is.
2.828
3.828
1.828
0.828.

⇒ The length of a traverse leg may be obtained by multiplying the latitude and.
secant of its reduced bearing
sine of its reduced bearing
cosine of its reduced bearing
tangent of its reduced bearing.

⇒ Which of the following is not the function of levelling head ?
to support the main part of the instrument
to attach the theodolite to the tripod
to provide a means for leveling the theodolite
none of the above

⇒ Which of the following methods of offsets involves less measurement on the ground?
method of perpendicular offsets
method of oblique offsets
method of ties
all involve equal measurement on the ground

⇒ The horizontal angle between the true meridian and magnetic meridian at a place is called
azimuth
declination
local attraction
magnetic bearing

⇒ Correction per chain length of 100 links along a slope of α radians, is.
100 Î±2
100 Î±
100 Î±3
100 Î±-1.

⇒ You have to observe an included angle with better accuracy than what is achievable by a vernier, you will prefer the method of.
repetition
reiteration
double observations
exactness.

⇒ The slope correction for a length of 30 m along a gradient of 1 in 20, is
3.75 cm
0.375 cm
37.5 cm
2.75 cm.

⇒ A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to.
cumulative, + 0.11 m
compensating, Â± 0.11 m
cumulative, - 0.11 m
none of these

⇒ Pick up the correct statement from the following :
The directions of plumb lines suspended at different points in a survey are not strictly parallel
In surveys of small extent, the effect of curvature may be ignored and the level surface of the earth is assumed as horizontal
In surveys of large extent, the effect of curvature of the earth must be considered
All the above.

⇒ The survey, in which the curvature of earth is ignored, is called as
Plane survey
Geodetic survey
Geological survey
Aerial survey

⇒ Hydrographic survey deal with the mapping of
Large water bodies
Rainfall data
Wave movement
None of the above

⇒ Pick up the correct statement from the following.
1 second of arc corresponds to a displacement ratio of 1:206, 300
1 degree of arc corresponds to a displacement ratio of 1:57
the angular errors tend to propagate themselves along a traverse as the square root of the number of stations
all the above.