Question is ⇒ The direction of rotation of a D.C. series motor can be changed by, Options are ⇒ (A) interchanging supply terminals, (B) interchanging field terminals, (C) either of (a) and (b) above, (D) None of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ The direction of rotation of a D.C. series motor can be changed by, Options are ⇒ (A) interchanging supply terminals, (B) interchanging field terminals, (C) either of (a) and (b) above, (D) None of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The direction of rotation of a D.C. series motor can be changed by
A.	interchanging supply terminals [Wrong Answer]
B.	interchanging field terminals [Correct Answer]
C.	either of (a) and (b) above [Wrong Answer]
D.	None of the above [Wrong Answer]
View Answer 11 -9 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The speed of a D.C. motor can be varied by varying
field current
applied voltage
resistance in series with armature
any of the above

⇒ Which of the following methods of braking is used in rolling mills ?
Dynamic braking
Plugging
Regenerative braking
Mechanical brakes

⇒ The speed of a D.C. series motor is
proportional to the armature current
proportional to the square of the armature current
proportional to field current
inversely proportional to the armature current

⇒ Regenerative braking on D.C. shunt motors is used when
the load has overhauling characteristics
the load is variable
the load also acts as a braking force
the load is constantly decreasing

⇒ Hopkinson's test is conducted at
no load
part load
low load
full load

⇒ The armature torque of the D.C. shunt motor is proportional to
field flux only
armature current only
both (a) and (b)
none of the above

⇒ Which of the following, in a D.C. motor, can sustain the maximum temperature rise ?
Commutator
Armature windings
Slip rings
Field windings

⇒ The generated e.m.f. and the current are in the opposite direction in case of
d.c. generators
d.c. motors
both (a) and (b)
none of the above

⇒ The simplest form of a motor controller is
relay
toggle switch
drum switch
magnetic switch

⇒ Which loss in a D.C. generator does not vary with load as well as flux density ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ In which of the following applications D.C. series motor is invariably tried?
Starter for a car
Drive for a water pump
Fan motor
Motor operation in A.C. or D.C.

⇒ What will happen if the back e.m.f. of a D.C. motor vanishes suddenly?
The motor will stop
The motor will continue to run
The armature may burn
The motor will run noisy

⇒ The speed of a D.C. shunt motor can be increased by
increasing the resistance in armature circuit
increasing the resistance in field circuit
reducing the resistance in the field circuit
reducing the resistance in the armature circuit

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ Small D.C. motors up to 5 H.P. usually have
2 poles
4 poles
6 poles
8 poles

⇒ In D.C. shunt motors as load is reduced
the speed will increase abruptly
the speed will increase in proportion to reduction in load
the speed will remain almost constant
the speed will reduce

⇒ Which of the following loss in a D.C. generator varies significantly with the load current ?
Field copper loss
Windage loss
Armature copper loss
None of the above

⇒ The mechanical power developed by a D.C. motor is equal to
power input + losses
back e.m.f. X armature current
power output X losses
power output X efficiency

⇒ Which D.C. motor Will have least percentage increase of input current for the same percentage increase in the torque?
Shunt motor
Series motor
Cumulative compound motor
Separately excited motor

⇒ Torque developed by a D.C. motor depends upon
active length of the conductor
current flow through the conductors
number of conductors
radius of armature

⇒ According to Fleming's left hand rule, when the forefinger points in the direction of the field or flux, the middle finger will point in the direction of
current, in the conductor
movement of conductor
resultant force on conductor
none of the above

⇒ As the load is increased the speed of D.C. shunt motor will
reduce slightly
increase slightly
increase proportionately -
remains unchanged

⇒ For which application a D.C. motor is preferred over an A.C. motor ?
High speed operation
Low speed operation
Fixed speed operation
Variable speed operation

⇒ The speed of a D.C. shunt motor is required to be more than full load speed. This is possible by
reducing the field current
decreasing the armature current
increasing the armature current
increasing the excitation current

⇒ Following motor is used where high starting torque and wide speed range control is required.
Single phase capacitor start
Induction motor
Synchronous motor
D.C. motor

⇒ If a D.C. motor is to be selected for conveyors, which motor would be preferred ?
Series motor
Shunt motor
Differentially compound motor
Cumulative compound motor

⇒ A motor for punching machine is usually subjected to
no load
continuous part load
continuous full load
intermittent load

⇒ A series motor is' best suited for driving
machine tools
cranes and hoists
shear and punches
none of the above

⇒ A wide and very sensitive speed control is usually required in case of
elevators
steel rolling mills
colliery winders
all of the above

⇒ Which of the following steps is likely to result in reduction of hysteresis loss in a D.C. generator ?
Providing laminations in armature core
Providing laminations in stator
Using non-magnetic material for frame
Using material of low hysteresis coefficient for armature core material