Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The difference in the lengths of an arc and its subtended chord on the earth surface for a distance of 18.2 km, is only. |

A. | 1 cm [Wrong Answer] |

B. | 5 cm [Wrong Answer] |

C. | 10 cm [Wrong Answer] |

D. | 100 cm. [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :Abdul Masroor Said on 2021-10-10 11:46:50C Faisal Rehman Said on 2020-02-21 09:01:450.1 m or 10 cm is correct answer for this question Amjad Ali Said on 2020-02-15 15:02:1310cm is correct Himanshu Gupta Said on 2019-06-24 09:01:45Correct answer is 'C' i.e. 10 cm. Sachin malap Said on 2019-03-16 12:00:3410 cm Shriram Bairwa Said on 2018-11-02 20:16:3512km mai 10mm 18.5km mai (10/12)*18.5=15.16mm ARUP DAS Said on 2018-05-10 11:29:42
Mayur dale Said on 2018-05-03 04:44:43According to ACE academy it is 10mm=1cm for 18.2km Prashant Rajput Said on 2018-04-18 15:10:471 cm Said on 2018-04-02 21:50:28 1cm Rameez Ahmad tantray Said on 2018-01-26 21:11:28C is correct option !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The error due to bad ranging is

Compensation

Cumulative positive

Cumulative negative

Both (B) and (C) above

⇒ For locating a distant object visible from two transit stations, the method usually preferred to, is.

Angles and distances from transit stations

Angles from two transit stations

distance from two transit stations

Angle from one transit station and distance from the other.

⇒ Which of the following methods of plane table surveying is used to locate the position of an inaccessible point ?

radiation

intersection

traversing

resection

⇒ The difference of levels between two stations A and B is to be determined. For best results, the instrument station should be

equidistant from A and B

closer to the higher station

closer to the lower station

as far as possible from the line AB

⇒ Magnetic bearing of a survey line at any place.

remains constant

changes systematically

varies differently in different months of the year

is always greater than true bearing.

⇒ The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is.

5.73Â°

5.37Â°

3.57Â°

3.75Â°.

⇒ Location of contour gradient for a high way is best set out from.

ridge down the hill

saddle down the hill

bottom to the ridge

bottom to the saddle.

⇒ An offset rod is provided at its top with

Hook

Flag

Distance measuring arrangement

None of these

⇒ The total change in level along the line is equal to total back sights.

minus total fore sights

the total rises minus total falls

the reduced level of last point minus reduced level of the first point

all the above.

⇒ The bearing of line

*AB*is 152° 30' and angle

*ABC*measured clockwise is 124° 28'. The bearing of

*BC*is.

27Â° 52'

96Â° 58'

148Â° 08'

186Â° 58'

⇒ Designation of a curve is made by :

angle subtended by a chord of any length

angle subtended by an arc of specified length

radius of the curve

curvature of the curve.

⇒ For a closed traverse the omitted measurements may be calculated.

length of one side only

bearing of one side only

both length and bearing of one side

all the above.

⇒ Irregular variation in magnetic declination may be due to

Magnetic storm

Earthquakes

Solar influence

Lunar influence

⇒ In a perfect prismatic compass.

magnetic axis and geometric axis of the needle coincide

ends of the needle and pivot are in same vertical and horizontal planes

pivot is vertically over the centre of the graduated circle

all the above.

⇒

*ABCD*is a regular parallelogram plot of land whose angle

*BAD*is 60°. If the bearing of the line

*AB*is 30°, the bearing of

*CD*, is.

90Â°

120Â°

210Â°

270Â°

⇒ The 'point of curve' of a simple circular curve, is.

point of tangency

point of commencement

point of intersection

mid-point of the curve

⇒ Quadrantal system confines the user to measure the bearing from

The north point clockwise

The north point or south point whichever is nearer

The north point anticlockwise

None of the above

⇒ In levelling operation,

The first sight on any change point is a back sight

The second sight on any change point is a fore sight

The line commences with a fore sight and closes with a back sight

The line commences with a back sight and closes with a foresight.

⇒ The theodolites used for making tacheometric observations by optical wedge system, are.

provided with stadia hairs in front of eye piece

not provided with stadia hairs at all

fitted with a glass wedge inside the telescope

fitted with a glass wedge in front of telescope.

⇒ If

*L*is in kilometres, the curvature correction is.

58.2 L2 mm

64.8 L2 mm

74.8 L2 mm

78.4 L2 mm.

⇒ Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling.

radiation

intersection

traversing

resection.

⇒ A correction for error due to refraction is

0-01 d

^{2}m

0-001 d

^{2}m

0.01122 d

^{2}m

0.078 d

^{2}m

⇒ Off sets are

Chain lines out of alignment

Small measurements from chain line

Measurements taken in chain surveying

None of the above

⇒ If the whole circle bearing of a line is 270°, its reduced bearing is.

N 90Â° W

S 90Â° W

W 90Â°

90Â° W.

⇒ Which of the following errors is not eliminated by the method of repetition of horizontal angle measurement ?

error due to eccentricity of verniers

error due to displacement of station signals

error due to wrong adjustment of line of collimation and trunnion axis

error due to inaccurate graduation

⇒ The angle between two plane mirrors of an optical square should be

30°

45°

60°

90°

⇒ Subtense tacheometry is generally preferred to if ground is.

flat

undulating

mountaineous

deserts.

⇒ Number of subdivisions per metre length of a levelling staff is.

100

200

500

1000

⇒ The line of collimation method of reduction of levels, does not provide a check on.

intermediate sights

fore sights

back sights

reduced levels.

⇒ In a lemniscate curve the ratio of the angle between the tangent at the end of the polar ray and the straight, and the angle between the polar ray and the straight, is.

2

3

4

3/2