Question is ⇒ the difference between the included angle and 180°., Options are ⇒ (A) vision gets obstructed, (B) chaining gets obstructed, (C) both vision and chaining get obstructed, (D) all the above., (E) , Leave your comments or Download question paper.

Question is ⇒ the difference between the included angle and 180°., Options are ⇒ (A) vision gets obstructed, (B) chaining gets obstructed, (C) both vision and chaining get obstructed, (D) all the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	the difference between the included angle and 180°.
A.	vision gets obstructed [Correct Answer]
B.	chaining gets obstructed [Wrong Answer]
C.	both vision and chaining get obstructed [Wrong Answer]
D.	all the above. [Wrong Answer]
View Answer 30 -116 Explanation:- Answer : A Discuss it below : ANMOL RAJ 15BCL0237 Said on 2020-05-18 00:15:29 It is traverse deflection angle Amjad Ali Said on 2020-02-15 14:48:22 What the nonsense is this Himanshu Gupta Said on 2019-06-24 08:11:35 the difference between the included angle and 180° : is called 'Deflection Angle' given options are irrelevant. !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The magnetic meridian at any point, is the direction indicated by a freely suspended
magnetic needle
and properly balanced magnetic needle
properly balanced and uninfluenced by local attractive force
magnetic needle over an iron pivot.

⇒ In chain surveying field work is limited to.
linear measurements only
angular measurements only
both linear and angular measurements
all the above.

⇒ Rankine's deflection angle in minutes is obtained by multiplying the length of the chord by.
degree of the curve
square of the degree of the curve
inverse of the degree of the curve
none of these.

⇒ Which of the following instruments is used for measurement of angles ?
Geodimeter
Tellurometer
Sextant
Telescope

⇒ In a constant level tube, size of the bubble remains constant because upper wall is.
of relatively larger radius
of relatively smaller radius
flat
convex downwards.

⇒ A negative declination shows that the magnetic meridian is to the
eastern side of the true meridian
western side of the true meridian
southern side of the true meridian
none of the above

⇒ Which one of the following mistakes/errors may be cumulative + or - :
bad ranging
bad straightening
erroneous length of chain
sag.

⇒ The first observation taken on a turning point is
Fore sight
Back sight
Both are correct
None of the above

⇒ In setting up a plane table at any station.
levelling is done first
centering is done first
both levelling and centering are done simultaneously
orientation is done first.

⇒ The adjustment of horizontal cross hair is required particularly when the instrument is used for
leveling
prolonging a straight line
measurement of horizontal angles
all of the above

⇒ Pick up the correct statement from the following :
the power of a lens is the reciprocal of its focal length
the power of a lens is the reciprocal of its focal length
the power of two or more thin lenses in contact is the power of the combination of the lenses
all the above.

⇒ For indirect ranging, number of ranging rods required, is.
1
2
3
4

⇒ Horizontal distances obtained by thermometric observations
require slope correction
require tension correction
require slope and tension corrections
do not require slope and tension corrections

⇒ Pick up the correct statement from the following :
it is difficult to eliminate an error completely at first trial
instability of the instrument makes it almost impossible to adjust it satisfactorily
adjustment screws must be left bearing firmly but should never be forced
all the above.

⇒ While rotating the theodolite in the horizontal plane, the bubble of the bubble tube takes up the same position in its tube, it indicates.
the rotation axis is vertical
the trummion axis is horizontal
the line of collimation is perpendicular to vertical axis
none of the above

⇒ True meridians are generally preferred to magnetic meridians because.
these converge to a point
these change due to change in time
these remain constant.
None of these.

⇒ The instrument used for accurate centering in plane table survey is
spirit level
alidade
plumbing fork
trough compass

⇒ Straight, parallel and widely spaced contours represent.
a steep surface
a flat surface
an inclined plane surface
curved surface.

⇒ An offset rod is provided at its top with
Hook
Flag
Distance measuring arrangement
None of these

⇒ Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to.
14.14
28.28 m
200 m
none of these.

⇒ The resection by two point problem as compared to three point problem
gives more accurate problem
takes less time
requires more labour
none of the above

⇒ The latitude of a traverse leg is obtained by multiplying its length by.
tangent of its reduced bearing
sign of its reduced bearing
cosine of its reduced bearing
cosecant of its reduced bearing.

⇒ Perpendicular offset from a tangent to the junction of a transition curve and circular curve is equal to.
shift
twice the shift
thrice the shift
four times the shift.

⇒ The surface of zero elevation around the earth, which is slightly irregular and curved, is known as.
mean sea level
geoid surface
level surface
horizontal surface.

⇒ Cross hairs in surveying telescopes, are fitted.
in the objective glass
at the centre of the telescope
at the optical centre of the eye piece
in front of the eye piece.

⇒ Two contour lines, having the same elevation.
cannot cross each other
can cross each other
cannot unite together
can unite together.

⇒ A back sight.
is always taken on a point of known elevation or can be computed
is added to the known level to obtain the instrument height
taken on an inverted staff is treated as negative
all the above.

⇒ The main plate of a transit is divided into 1080 equal divisions. 60 divisions of the vernier coincide exactly with 59 divisions of the main plate. The transit can read angles accurate upto.
5"
10"
15"
20"

⇒ The box of prismatic compass is made of
Steel
Brass
Iron
Aluminium

⇒ The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as.
Plane alidade
telescopic alidade
clinometer
tacheometer.