Question is ⇒ The design of wave filter is based on characteristic impedance which is, Options are ⇒ (A) pure resistance, (B) pure reactance, (C) pure resistance in pass band and pure reactance in attenuation band, (D) pure reactance in pass band and pure resistance in attenuation band, (E) , Leave your comments or Download question paper.

Question is ⇒ The design of wave filter is based on characteristic impedance which is, Options are ⇒ (A) pure resistance, (B) pure reactance, (C) pure resistance in pass band and pure reactance in attenuation band, (D) pure reactance in pass band and pure resistance in attenuation band, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The design of wave filter is based on characteristic impedance which is
A.	pure resistance [Wrong Answer]
B.	pure reactance [Wrong Answer]
C.	pure resistance in pass band and pure reactance in attenuation band [Correct Answer]
D.	pure reactance in pass band and pure resistance in attenuation band [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The proper exponential form of - 0.0032 in FORTRAN 77 is
-3.2 E - 3
-0.0032
-0.00032 EI
-0.032 E - 1

⇒ Which of the following operation are performed on linear queues?

Testing a linear queue for underflow
Enqueue operation
Dequeue operation
Testing a linear queue for overflow.

Select the correct answer using the codes given below the lists
1, 2 and 3
2, 3 and 4
1, 3 and 4
1, 2, 3 and 4

⇒ Consider the following ON GO TO statement in Ba
10, 20, 30, 20 respectively
10, 20, 20, 30 respectively
20, 30, 20, 10 respectively
10, 30, 20, 20 respectively

⇒ What was the first commercial geostationary communication satellite?
INTELSAT 1
ECHO
INSAT-1A
SPUTNIK

⇒ ECL has high switching speed because the transistors are
switching between cutoff and saturation regions
switching between cutoff and active regions
switching between active and saturation regions
none of the above

⇒ Schering bridge operates at a high voltage of about 10 kV.
TRUE
FALSE

⇒ In a reflex klystron the output frequency is determined primarily by resonant frequency of cavity.
TRUE
FALSE

⇒ In active filters inductances are divided because they
are always associated with same resistance
are bulky and unsuitable for miniaturization
are non linear
saturate quickly

⇒ Roughly the time required for microwave cooking as compared to conventional cooking is
about twice
about half
about 10 times
about one-tenth

⇒ For a high pass filter, β = p in attenuation band.
TRUE
FALSE

⇒ If f_s be the signal frequency and f_i be the intermediate frequency then image frequency is given by
f_s + f_i
f_s ± f_i
f_s ± 2f_i
f_s + 2f_i

⇒ In a 4-ary FSK, the frequencies are separated by f_s. Then they are
in phase
in phase opposition
orthogonal
none of the above

⇒ Which of the following is true as regards photo emission?
Velocity of emitted electrons is dependent on light intensity
Rate of photo emission is inversely proportional to light intensity
Maximum velocity of electron increases with decreasing wave length
Both holes and electrons are produced

⇒ Which of these has 3 layers?
PIN diode
Zener diode
Schottky diode
Photo diode

⇒ Given below a block diagram of oscillator circuit with various reactance elemen
x₁ = C, x₂ = L, x₃ = C
x₁ = C, x₂ = L, x₃ = L
x₁ = C, x₂ = C, x₃ = L
x₁ = L, x₂ = C, x₃ = L

⇒ Most of the transistor data sheets specify the power rating for an ambient temperature of
10°C
25°C
50°C
75°C

⇒ In figure, V_{0-1 V
2 V
+1 V
+15 V}

⇒ In a p-n-p transistor the main current carriers and the mechanism of flow respectively are
electrons, drift
holes, drift
holes, diffusion
electrons, diffusion

⇒ Resistivity of carbon is around
10 to 70 m-ohm-cm
80 to 130 m-ohm-cm
800 to 1300 m-ohm-cm
8000 to 13000 m-ohm-cm

⇒ If E_b, the energy per bit of a binary digital signal is 10^-6 watt sec. and the one sided power spectral density of the white noise N₀ = 10^-5 W/Hz, then the output SNR of the matched filter is
26 dB
10 dB
20 dB
13 dB

⇒ In a half wave diode rectifier circuit the current flows in the load circuit for
90° in each cycle
180° in each cycle
270° in each cycle
360° in each cycle

⇒ Two 2 port circuits are connected cascaded. To determine the response, it is more convenient to use
O.C. impedance parameters
S.C. admittance parameters
ABCD parameters
h parameters

⇒ The circuit of figur
Precision integrator
Hartley oscillator
Butterworth high pass filter
Wien bridge oscillator

⇒ A line has Z₀ = 300 ∠ 0° Ω. If Z_L = 150 ∠ 0° Ω, reflection coefficient is
0.5
0.3333
-0.3333
-0.5

⇒ The 2's complement representation of the decimal number -4 is
100
1100
1011
1010

⇒

Match the following:

	List I (I/P - O/P relation)		List II (Property of the system)
A.	y(n) = x(n)	1.	Nonlinear, non-causal
B.	y(n) = x(n²)	2.	Linear, non casual
C.	y(n) = x²(-n)	3.	Linear causal
D.	y(n) = x²(n)	4.	Nonlinear causal

A-1, B-4, C-3, D-2
A-3, B-2, C-1, D-4
A-1, B-2, C-3, D-4
A-3, B-4, C-1, D-2

⇒ The voltage transfer functions of two port circuits connected in cascade can be easily found from
product of individual ABCD matrices
product of voltage transfer functions of two networks
sum of z matrices
sum of h matrices

⇒ A RADAR can be used to
aim a gun at an aircraft
to direct guided missiles
to search submarines
all of the above

⇒ In figure V_CE (sat) = 0.1 V. Then I_C (sa
10 mA
20 mA
30 mA
40 mA

⇒ Directivity of antenna is defined as
maximum directive gain
average directive gain
∞
0