Question is ⇒ The depth of penetration at 4 MHz is 10 cm, then at 2.5 MHz it is, Options are ⇒ (A) 62.5 cm, (B) 13 cm, (C) 6.25 cm, (D) 8 cm, (E) , Leave your comments or Download question paper.

Question is ⇒ The depth of penetration at 4 MHz is 10 cm, then at 2.5 MHz it is, Options are ⇒ (A) 62.5 cm, (B) 13 cm, (C) 6.25 cm, (D) 8 cm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The depth of penetration at 4 MHz is 10 cm, then at 2.5 MHz it is
A.	62.5 cm [Wrong Answer]
B.	13 cm [Correct Answer]
C.	6.25 cm [Wrong Answer]
D.	8 cm [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If the oscillator output is modulated by audio frequencies upto 10 kHz, the frequency range occupied by the side bands will be
711.9 kHz to 712.1 kHz
702 kHz to 722 kHz
692 kHz to 732 kHz
71.2 kHz to 71.20 kHz

⇒ A short vertical grounded antenna is required to radiate at 1 MHz. The effective height of the antenna is 302 m. The calculated value of radiation resistance is
1.58 Ω
158 Ω
15.8 Ω
none

⇒ In a low power factor wattmeter, compensation for pressure coil current is provided.
TRUE
FALSE

⇒ Shifting digits from left to right and vice versa is needed in
storing numbers
arithmetic operations
counting
storing and counting

⇒ In the signal flow graph in the given figure the number of forward paths and pairs of non-touching loops are respecti
3 and 1
3 and 2
4 and 2
2 and 4

⇒ The phase angle curve of G(jω) H(jω) is drawn by adding the phase angles of individual factors.
TRUE
FALSE

⇒ Half power point directions for broadside is
60°
30°
45°
at any angle

⇒ The signal y(t) = x(- t) is __________ .
causal
non-causal
depends on x(t)
none of these

⇒ In the BJT amplifier shown in the figure is the transistor is biased in the forward active region. Putting a capacitor across R_E
decrease the voltage gain and decrease the I/P impedance
increase the voltage gain and decrease the I/P Impedance
decrease the voltage gain and Increase the I/P impedance
none of the above

⇒ What will be the propagation constant at 10 MHz?
3.4 radians/km
34.4 radians/km
344 radians/km
3440 radians/km

⇒ A sinusoidal ac voltage of amplitude 100 V is applied to a rectifying device which offers 10 Ω resistance in forward direction and infinite resistance in reverse direction. The reading on hot wire ammeter will be
0.416666666666667
0.208333333333333
3.185 A
1.414 A

⇒ Both Impatt and Trapatt devices use avalanche effect
TRUE
FALSE

⇒ An increase in ambient temperature means that maximum power rating of transistor
will increase
will decrease
may increase or decrease
may increase or remain the same

⇒ The internal resistance of a current source used in the model of a BJT while analyzing a circuit using BJT is :
very high
very low
zero
of the order of a few mega ohms

⇒ Which of the following microphones has lowest output impedance?
Moving coil
Ribbon
Crystal
Condenser

⇒ Transverse electric (TE) waves have
electric field component E in the direction of propagation
magnetic field component H in the direction of propagation
magnetic field component H in the direction of propagation and no component of electric field E in this direction
electric field component E in the direction of propagation and no component of magnetic field H in this direction

⇒ Consider the cascade structure of two filte
1 and 3
only 2
2 and 3
only 3

⇒ Which of the following amplifiers has a voltage gain of less than 1?
CE
CC
CB
CE or CB

⇒ The low pass filter characteristic shown in figure realiza
TRUE
FALSE

⇒ A noiseless 3 KHz channel can transmit binary at the rate __________ .
12000 bps
10000 bps
6000 bps
3000 bps

⇒ A sine wave with slew rate distortion looks like
step wave
square wave
triangular wave
cosine wave

⇒ Avalanche beakdown is primarily dependent on the phenomenon of
doping
collision
recombination
ionization

⇒ Which two rows represent identical binary numbers?
A second and fourth
Fifth and eight
Third and seventh
Second and third

⇒

Assertion (A): Typical value of thermal resistance from source to sink of an SCR is about 0.3° C/W

Reason (R): Heat sinks of thyristors are generally made of aluminium.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Two coupled coils have self inductance L₁ and L₂. The coefficients of coupling is k. The mutual inductance is
k L₁L₂
k²L₁L₂
kL₁L₂
kL₁L₂

⇒ Which of the following produces upper and lower side frequencies?
Microphone
Demodulator in a superheterodyne receiver
Modulator in a. radio transmitter
Oscillator in a receiver

⇒ In 8085 microprocessor, in order to enable RST 5.5, RST 6.5 and RST 7.5 interrupts, which of the following instruction are needed?
EI only
SIM only
EI and SIM both
None

⇒ A single phase half wave converter is feeding a resistive load. Output dc power is P_dc and total power delivered to load is P_ac then
P_dc = P_ac for all values of firing angles
P_dc = P_ac if firing angle is less than 180°
P_dc < P_ac for all values of firing angles
P_dc < P_ac if firing angle is less than 180°

⇒

Match the following:

	List I		List II
A.	RF amplifier	1.	Amplifier received carrier and sidebands
B.	Loudspeaker	2.	Gives acoustic output
C.	Demodulator	3.	Has IF input and AF output
D.	IF amplifier	4.	Fixed-tuned to intermediate frequency

A-1, B-2, C-3, D-4
A-2, B-1, C-3, D-4
A-3, B-4, C-1, D-2
A-1, B-4, C-3, D-2

⇒

Assertion (A): In a conductor, current density remains constant in time as long as E is constant.

Reason (R): In a conductor, J = σE.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true