Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The deformation of the bar per unit length in the direction of the force is known as. |

A. | linear strain [Correct Answer] |

B. | lateral strain [Wrong Answer] |

C. | volumetric strain [Wrong Answer] |

D. | shear strain [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A closely coiled helical spring is of mean diameter (

*D*) and spring wire diameter (

*d*). The spring index is the ratio of.

1/d

1/D

D/d

d/D

⇒ The deformation of the bar per unit length in the direction of the force is known as.

linear strain

lateral strain

volumetric strain

shear strain

⇒ Two closely coiled helical springs '

*A*' and '

*B*' are equal in all respects but the number of turns of spring '

*A*' is half that of spring '

*B*' The ratio of deflections in spring '

*A*' to spring '

*B*' is?

1/8

1/4

1/2

2

⇒ If a material expands freely due to heating it will develop

thermal stresses

tensile stress

bending

compressive stress

⇒ In a leaf spring, the length of all the leaves are equal.

True

False

Disagree

None of these

⇒ The buckling load for a given column depends upon

area of cross-section of the column

length and least radius of gyration of the column

modulus of elasticity for the material of the column

all of the above

⇒ Which of the following statement is correct?

The size of hole drilled in riveting plates is less than the actual size of rivet.

The centre to centre distance between two consecutive rivets in a row is called margin.

Rivets are generally specified by its shank diameter.

Tearing of plates can be avoided by taking the pitch of rivets equal to 1.5 times the diameter of rivet hole.

⇒ The point of contraflexure occurs in?

cantilever beams

simply supported beams

overhanging beams

fixed beams

⇒ A reinforced cement concrete beam is considered to be made of.

homogeneous material

hetrogeneous material

composite material

isotropic material

⇒ When one plate overlaps the other and the two plates are riveted together with two rows of rivets, the joint is known as.

single riveted lap joint

double riveted lap joint

double riveted single cover butt joint

double riveted double cover butt joint

⇒ In case of an under-reinforced beam, the depth of actual neutral axis is __________ that of the critical neutral axis.

same as

less than

greater than

Both (a) and (b)

⇒ Compression members always tend to buckle in the direction of the?

axis of load

perpendicular to the axis of load

minimum cross section

least radius of gyration

⇒ In riveted boiler joints, all stresses, shearing, bearing and tensile are based on the

size of rivet

size of the drilled or reamed hole

average of size of rivet and hole

smaller of the two

⇒ The shear force at the ends of a simply supported beam carrying a uniformly distributed load of

*w*per unit length is.

zero at its both ends

wl at one end and - wl at the other end

wl/2 at one end and - wl/2 at the other end

wl2/2 at one end and - wl2/2 at the other end

⇒ The bending moment diagram for a simply supported beam loaded in its centre is.

a right angled triangle

an issoscles triangle

an equilateral triangle

a rectangle

⇒ A thin cylindrical shell of diameter (

*d*), length (

*l*) and thickness (

*t*)is subjected to an internal pressure (

*p*). The hoop stress in the shell is

pd/t

pd/2t

pd/4t

pd/6t

⇒ Percentage reduction of area in performing tensile test on cast iron may be of the order of

50%

25%

0%

15%

⇒ The total strain energy stored in a body is termed as.

resilience

proofresilience

impact energy

modulus of resilience

⇒ If the radius of wire stretched by a load is doubled, then its Young's modulus will be

doubled

halved

become four times

become one-fourth

⇒ The property of a material by virtue of which a body returns to its original, shape after removal of the load is called

plasticity

elasticity

ductility

malleability

⇒ A non-yielding support implies that the

support is frictionless

support can take any amount of reaction

support holds member firmly

slope of the beam at the support is zero

⇒ In order to know whether a column is long or short, we must know its slenderness ratio.

True

False

incorrect

none of these

⇒ A column that fails due to direct stress, is called.

short column

long column

weak column

medium column

⇒ When a body is subjected to a direct tensile stress (σ) in one plane, then normal stress on an oblique section of the body inclined at an angle θ to the normal of the section is

Ïƒ cos Î¸

Ïƒ cos2 Î¸

Ïƒ sin Î¸

Ïƒ sin2 Î¸

⇒ A riveted joint may fail by.

tearing of the plate at an edge

tearing of the plate across a row of rivets

shearing of rivets

any one of these

⇒ The ratio of the largest load in a test to the original cross-sectional area of the test piece is called.

elastic limit

yield stress

ultimate stress

breaking stress

⇒ The radius of the Mohr s circle in the given figure is equal to

sum of two principal stresses

sum of two principal stresses

half the sum of two principal stresses

half the difference of two principal stresses

⇒ Rivets are made of following type of material

tough

hard

resilient

ductile

⇒ A thin cylindrical shell of diameter (

*d*) and thickness (

*t*) is subjected to an internal pressure (

*p*). The ratio of longitudinal strain to volumetric strain is

m-1/2m-1

2m-1/m-1

m-2/3m-4

m-2/5m-4

⇒ The line of intersection of the neutral layer with any normal cross-section of the beam is called neutral axis.

True

False

Incorrect

None of these