Question is ⇒ The counter which require maximum number of FF for a given mod counter is, Options are ⇒ (A) Ripple counter, (B) BCD counter, (C) Ring counter, (D) Programmed counter, (E) , Leave your comments or Download question paper.

Question is ⇒ The counter which require maximum number of FF for a given mod counter is, Options are ⇒ (A) Ripple counter, (B) BCD counter, (C) Ring counter, (D) Programmed counter, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The counter which require maximum number of FF for a given mod counter is
A.	Ripple counter [Wrong Answer]
B.	BCD counter [Wrong Answer]
C.	Ring counter [Correct Answer]
D.	Programmed counter [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a half bridge inverter, the freewheeling diodes are needed
even when load is resistive
only when load is inductive
only when load is inductive or capacitive
for all types of loads

⇒ Which of the following frequencies has the greatest period?
20 Hz
200 Hz
20 kHz
200 kHz

⇒ Which of the following materials in not an insulator?
Diamond
Graphite
Bakelite
Lucite

⇒ The refractive index of E layer at frequency of 81 N
0
∞
1
0.5

⇒ KCL is a statement of principle of conservation of energy.
TRUE
FALSE

⇒ An FM signal with a deviation is passes through the mixer, and has its frequency reduced five fold. The deviation in the output of the mixer is
Δ
5Δ
Δ/5
indeterminant

⇒ In FM modulation pre-emphasis is done for
high frequency components
low frequency components
middle frequency components
both (a) and (b)

⇒ The depletion layer consists of immobile ions.
TRUE
FALSE

⇒ If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be
a voltage source
a current source
both of the above
none of the above

⇒ In N-type semiconductor
electrons are majority carriers while holes are minority carriers
electrons are majority carriers while holes are majority carriers
both electrons as well as holes are majority carriers
both electrons as well as holes are minority carriers

⇒ A coaxial RF cable has a characteristic impedance of 50 Ω and C equal to 40 pF/m. The inductance is
1 μ H/m
10 μ H/m
0.1 μ H/m
0.01 μ H/m

⇒ A 3 phase ac regulator uses
3 thyristors
6 thyristors
9 thyristors
12 thyristors

⇒ Consider the following statements

Tellegen's theorem is applicable to any lumped network.
Reciprocity theorem is applicable to linear bilateral network.
Thevenin theorem is applicable to two terminal linear active network.
Norton's theorem is applicable to linear active network.

Which of the above statements are correct?
1, 2 and 3
1, 2, 3 and 4
1, 2 and 4
3 and 4

⇒ For the network shown below, if V_D = 12 V and V_GSQ = - 2 V value of R_S wil
13.35 kΩ
3.35 kΩ
33.31 kΩ
3.95 kΩ

⇒ A 6 bit dual slope A/D converter uses a reference of -6v and a 1 MHz clock. It uses a fixed count of 40 (101000). Then, what will be input, if the output register shows 100111 at the end of conversion.
5.85 V
6 V
5 V
10 V

⇒ Thermal noise is independent of
temperature
bandwidth
centre frequency
Boltzmann constant

⇒ Consider the following applications

Switch
Attenuator
Phase shifter
Oscillator

In which of the above can a PIN diode be used?
1 2 3 and 4
1 2 and 3 only
1 and 2 only
2, 3 and 4 only

⇒ A P-N junction diode dynamic conductance is directly proportional to
the applied voltage
the temperature
its current
thermal voltage

⇒ A TV receiver is 40 cm wide and 30 cm high. The EHT supply required is about
2kV
20 kV
53 kV
10 W

⇒ Which of the following methods is used for solving differential equations numerically?
Runge-Kutta method
Gauss-elimination method
Newton-Raphson method
Any one of these

⇒ To couple a coaxial line to a parallel wire line it is best to use
slotted line
balun
directional coupler
λ/4 transformer

⇒ Which of the following microphones is used as a standard for calibration?
Moving coil
Carbon
Condenser
Ribbon

⇒ In 8085 microprocessor, what is the length of temporary register?
6 bits
8 bits
12 bits
16 bits

⇒ Ohmic range of carbon composition resistors is
10 to 100 ohms
10 to 10 K ohms
10 to 200 ohms
10 to 25 M ohms

⇒ Consider the instructions

MOV M, B
OUT 4
LDA X

Which of the above uses IO/W cycle?
1 only
1 and 2 only
2 only
3 only

⇒ A speech signal, band limited to 4kHz and peak voltage varying between + 5V and - 5V is sampled at the Nyquist rate. Each sample is quantized and represented by 8 bits. Assuming the signal to be uniformly distributed between its peak values, the signal to noise ratio at the quantizer output is
156 dB
32 dB
48 dB
64 dB

⇒ For a level input sequential circuit
output in a level only
output is in the pulse form
output may be a pulse or a level form
none of these

⇒ For BJT transistor. The maximum power dissipation is specified as 350 mW if ambient temperature is 25°C. If ambient temperature is 60°C the maximum power dissipation should be limited to about
100 mW
250 mW
450 mW
600 mW

⇒

Match the following:

	List I (Types of transmission structure)		List II (Modes of propagation)
A.	Strip line	1.	Quasi TEM
B.	Hollow rectangular waveguide	2.	Pure TEM
C.	Microstrip	3.	TE/TM
D.	Corrugated waveguide	4.	Hybrid

A-2, B-1, C-3, D-4
A-4, B-1, C-3, D-2
A-2, B-3, C-1, D-4
A-4, B-3, C-1, D-2

⇒

Assertion (A): A backward wave oscillator has an internal positive feedback.

Reason (R): A positive feedback is necessary for sustained oscillations.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct