Question is ⇒ The correct sequence of events to improve system stability is, Options are ⇒ (A) insert derivative action, use negative feedback, reduce gain, (B) reduce gain, use negative feedback, insert derivative action, (C) reduce gain, insert derivative feedback, use negative feed back, (D) use negative feedback, reduce gain, insert derivative action, (E) , Leave your comments or Download question paper.

Question is ⇒ The correct sequence of events to improve system stability is, Options are ⇒ (A) insert derivative action, use negative feedback, reduce gain, (B) reduce gain, use negative feedback, insert derivative action, (C) reduce gain, insert derivative feedback, use negative feed back, (D) use negative feedback, reduce gain, insert derivative action, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The correct sequence of events to improve system stability is
A.	insert derivative action, use negative feedback, reduce gain [Wrong Answer]
B.	reduce gain, use negative feedback, insert derivative action [Wrong Answer]
C.	reduce gain, insert derivative feedback, use negative feed back [Wrong Answer]
D.	use negative feedback, reduce gain, insert derivative action [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The signal flow graph of a system is shown in the given figure. The effect of disturbance T_D can be reduce
increasing G₂ (s)
decreasing G₂ (s)
increasing G₁ (s)
decreasing G₁ (s)

⇒ The units of resistivity are ohm-metre.
TRUE
FALSE

⇒ In a megger the controlling torque is provided by
spring
gravity
coil
eddy current

⇒ The number of stator field windings in an ac tachometer are
1
2
3
4

⇒ The method of frequency compensation in moving iron voltmeter is
to use a capacitor in series with coil
to connect a capacitor in parallel with coil
to connect a capacitor in parallel with series resistance
none of the above

⇒ In a full wave diode rectifier circuit each diode carries current for
90° in each cycle
180° in each cycle
270° in each cycle
360° in each cycle

⇒ The damping ratio of a pair of complex poles when expressed in terms of angle θ measured from jω axis equal to
sin θ
cos θ
tan θ
cot θ

⇒ As temperature increases, the temperature coefficient of metals increases.
TRUE
FALSE

⇒ For the system in the given figure, the characteristic equation
s² + s(3 + 6a) + 6 = 0
s² + s(3 + 12a) + 12 = 0
s² + 3s = 0
s² + 6s = 0

⇒ The memory hierarchy in microprocessor based system is
register, cache, primary, mass, off line back up
cache, register, primary, mass, off line back up
cache, register, mass, primary, off line back up
register, cache, mass, primary, off line back up

⇒ If the output current wave shape of class C circuit has a period of 1 μs and a pulse width of 0.006 μs, the duty cycle is
0.06
0.006
0.00006
0.0006

⇒ In the following limiter circuit, an input voltage V₁ = 10 sin 100pt applied. Assume that the diode drop is 0.7 V when it is forward biased. The zener breakdown voltage is 6
6.1 V, -0.7 V
0.7 V, -7.5 V
7.5 V, -0.7 V
7.5 V, -7.5 V

⇒ The entries in the first column of Routh array of a fourth order are 5, 2, - 0.1, 2, 1. The number of poles in the right half plane are
1
2
3
4

⇒ In the given figure shows a 3 bit shift register using TTL flip flops. Initially all the flip flops are set to 0 state. After 8 clock pul
A = 1, B = 1, C = 1
A = 1, B = 1, C = 0
A = 0, B = 1, C = 1
A = 0, B = 0, C = 1

⇒ EEPROM is also known as
UVPROM
EAPROM
both UVPROM and EAPROM
none of the above

⇒ The accumulator drives the ALU.
TRUE
FALSE

⇒ 100101₂ is equal to decimal number
47
37
21
17

⇒ A single element strain gauge bridge has two fixed resistances R₁ and R₁ of 120 Ω each and a variable resistance which gives full deflection at 120 Ω for zero strain and 120.6 Ω for straine e. If gauge factor is 2, strain e is
0.0025
0.0035
0.005
0.0075

⇒ A combination circuit is one in which the output depends on
input combination at that time
input combination and previous output
input combination and previous input
present output and previous output

⇒ Industrial noise has the frequency range of
1 to 100 Hz
200 to 5000 Hz
above 200 MHz
1 to 600 MHz

⇒ Consider the following statements as regards advantages of CCD sensors as camera pick up tube

High sensitivity
Good spectral response
Image lag absent

Out of the above which are correct
1, 2, 3
1, and 2 only
1 and 3 only
2 and 3 only

⇒ In Pascal an array declaration provides information to the Pascal processor to enable it to
identify the variable as an array name
reserve memory locations to store all the components of array
check the values computed for subscripts expressions during program execution with the specified lower and upper limits of subscripts
all of the above

⇒ In figure, the switch has been in closed position for a long time. At t = 0, the switch is opened. At t = 0⁺, the current R_{10.333333333333333
0.166666666666667
0.25
0.0833333333333333}

⇒ A linear system is characterized by H(ω) = Be^-2ω² the system is physically
unrealizable
realizable
depends upon B
depends upon constant 2

⇒ The secondary lobes in binomial arrays can be reduced by
maintaining spacing between two consecutive radiating sources less than λ/2
maintaining the amplitudes in radiating sources, from outer towards the centre source, proportional to the coefficients of the successive terms of the binomial series
both (a) and (b)
none of the above

⇒ A mobile telephone has a range of about
50 km
10 km
1 km
0.1 km

⇒ A surface charge density of 8 nc/m² is present on a plane x = z. A line charge density of 30 nC/m is present on line x = 1, y = 2 Find V_AB for points A(3, 4, 0) and B(4, 0, 1)
583.38 V
58.338 V
583.38 mV
58.338 mV

⇒ The orbital period of a geostationary communication satellite is
12 hours
24 hours
36 hours
48 hours

⇒ In a specimen of n type semiconductor, the initial concentration of holes and electrons is p_no and n_no. When the specimen is subjected to radiation, the hole and electron concentration increase to p_n and n_n. Then
p_n - p_no = n_n - n_no
p_n + p_no = n_n + n_no
p_n - p_no = n_no + n_no
p_n + p_no = n_n - p_no

⇒ Huffman code is also known as redundancy code
TRUE
FALSE
in some cases
depend upon efficiency