Question is ⇒ The common emitter short circuit current gain β of a transistor, Options are ⇒ (A) is a monotonically increasing function of the collector current Ic, (B) is a monotonically decreasing function of Ic, (C) increasing with Ic, for low Ic, reaches a maximum and then decreases with further increase in Ic, (D) is not a function of Ic, (E) , Leave your comments or Download question paper.

Question is ⇒ The common emitter short circuit current gain β of a transistor, Options are ⇒ (A) is a monotonically increasing function of the collector current Ic, (B) is a monotonically decreasing function of Ic, (C) increasing with Ic, for low Ic, reaches a maximum and then decreases with further increase in Ic, (D) is not a function of Ic, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The common emitter short circuit current gain β of a transistor
A.	is a monotonically increasing function of the collector current I_c [Wrong Answer]
B.	is a monotonically decreasing function of I_c [Wrong Answer]
C.	increasing with I_c, for low I_c, reaches a maximum and then decreases with further increase in I_c [Correct Answer]
D.	is not a function of I_c [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The use of microprocessor control in automobiles results in
improved fuel economy
improved car control
advanced information system for driver
all of the above

⇒ In solids the current flow is due to electrons only.
TRUE
FALSE

⇒ A heavily doped semiconductor exhibits a __________ such a device is called sensistors.
negative temperature coefficient of resistance
positive temperature coefficient of resistance till a particular value of temperature and then it shown negative temperature coefficient of resistance
positive temperature coefficient of resistance
none of the above

⇒

Match the following:

	List I		List II
A.	Laser	1.	Emits monochromatic light of low intensity
B.	Solar cell	2.	Consumes electrical power due to incident light
C.	Photodiode	3.	Delivers power to a load
D.	LED	4.	Emits monochromatic light of high intensity

A-4, B-3, C-1, D-2
A-3, B-4, C-2, D-1
A-4, B-3, C-2, D-1
A-3, B-4, C-1, D-2

⇒ For a binary half subtractor having two inputs A and B the correct sets of logical expressions for the outputs D (A - B) and X = Borrow are
D = AB + AB, X = AB
D = AB AB, X = AB
D = AB + AB, X = AB
D = AB + A B, X = AB

⇒ For a good conducting medium the intrinsic impedance is
σωμ ∠p/2
ωμ /σ ∠45°
ωμ/σ ∠p/2
ωμ/σ ∠0°

⇒ Which one is time invariant system?
y[n] = x[2n]
y[n] = x[n] x[n - 1]
y[n] = x[n/2]
all

⇒ Some typical examples of macroscopic quantities are
conductivity
µ_r
dielectric constant
all of the above

⇒ If x = 0.1396 radians, the values of 1 - cos x and 2 sin² (x / 2) using floating point arithmetic with a 4 digit mantissa are respectively
.1000 E - 1 each
.9727 E - 2 each
.1000 E - 1 and .9727 E - 2 respectively
.9727 E - 2 and .1000 E - 1 respectively

⇒ For the minterm designation Y = ∑ m (1, 3, 5, 7) the complete expression is
Y = A BC + A B C
Y = A B C + A B C + ABC + A BC
Y = A B C + A B C + ABC + A BC
Y = A B C + ABC + A BC + A BC

⇒ When a trivalent impurity is added, the semiconductor becomes
p type
n type
intrinsic
neutral

⇒ Which of the following best represents the input impedance of an actual op-amp?
10 ohm
1 k ohm
1 M ohm
100 M ohm

⇒ A RADAR can be used to
aim a gun at an aircraft
to direct guided missiles
to search submarines
all of the above

⇒ An SCR is triggered at 80° in the positive half cycle, only. The rms anode current is 25 A. If the firing angle is changed to 160°, the rms current is likely to be
25 A
12.5 A
less than 25 A
less than 12.5 A

⇒ Data can be changed from spatial code to temporal code and vice-versa by using
ADC and DAC
shift Register
synchronous counter
timers

⇒

Assertion (A): In C a variable name can have upto 8 characters and special symbols can also be part of variable name.

Reason (R): In C a type declaration at the beginning of program indicates the type of variable name used in the program.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ Consider the following statements about constants in 8085

The assembler treats 64 H as hexadecimal constant.
The assembler treats 154 as binary constant.
The assembler treats 540 as octal constant.
The assembler treats 138 as decimal constant.

Which of the above are correct?
1, 2 and 3 only
1, 3 and 4 only
1 and 3 only
2 and 4 only

⇒ The v-i characteristic shown in the given figure is
thermistor
photoconductor
varistor
none of the above

⇒ The advantage of using crystal oscillator is that it
requires low d.c. supply voltage
works at high frequency
gives high output voltage
gives constant frequency of oscillations

⇒ If the functions w, x, y, z are as foll
w = z x = z
w = z, x = y
w = y
w = y = z

⇒ Satellite launch sites are invariably located on Eastern seaboards to ensure that
launch takes place eastward
expenditure of propulsion fuel is reduced during plane changing
the satellite achieves circular orbit quickly
spent rocket motor and other launcher debris falls into the sea

⇒ Material which lack permanent magnetic dipoles are known as
paramagnetic
diamagnetic
ferromagnetic
ferrimagnetic

⇒

Match the following:

	List I		List II
A.	On-off	1.	steam kettle with different settings
B.	Proportional	2.	Elevator
C.	Cascade	3.	Robot-positioning
D.	Digital	4.	Domestic Refrigerator

A-4, B-2, C-3, D-1
A-2, B-4, C-1, D-3
A-3, B-1, C-4, D-2
A-4, B-2, C-1, D-3

⇒ A clock signal coordinates the working of different flip flops.
TRUE
FALSE

⇒ A seven bit code (even parity) 1111101 may have error. The correct code is
1111101
1111111
101011
1100011

⇒ In 8156, the lower times byte is addressed with 24 H, and the upper times byte with
20 H
23 H
24 H
25 H

⇒

Assertion (A): When performance specifications are given in term of transient response characteristics, root locus method is a suitable method.

Reason (R): When performance specifications in terms of state variables are given, modern control methods can be used.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ The normalised form of 1.81 x 10^-11 is
18.1 x 10^-12
18.1 x 10^-13
0.181 x 10^-10
0.0181 x 10^-9

⇒ For type 1 system the velocity lag error is
inversely proportional to bandwidth of system
directly proportional to gain constant
inversely proportional to gain constant
independent of gain constant

⇒ For overdamped systems a quadratic factor in transfer function can be replaced by two first order factors with real poles
TRUE
FALSE