Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The bending stress in abeam is __________ bending moment. |

A. | equal to [Wrong Answer] |

B. | less than [Wrong Answer] |

C. | more than [Wrong Answer] |

D. | directly proportional to [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The maximum tangential stress in a thick cylindrical shell is always __________ the internal pressure acting on the shell.

equal to

less than

greater than

high than

⇒ In the above question, the normal stress on an oblique section will be maximum, when θ is equal to

0Â°

30Â°

45Â°

90Â°

⇒ For which material the Poisson's ratio is more than unity

steel

copper

aluminum

cast iron

⇒ Shear modulus is the ratio of

linear stress to linear strain

linear stress to lateral strain

volumetric strain to linear strain

shear stress to shear strain

⇒ The ratio of linear stress to the linear strain is called

modulus of rigidity

modulus of elasticity

bulk modulus

Poisson's ratio

⇒ The maximum shear stress developed in a beam of circular section is __________ the average shear stress.

equal to

4/3 times

1.5 times

twice

⇒ The deformation of a bar under its own weight compared to the deformation of same body subjected to a direct load equal to weight of the body is

same

double

half

four times

⇒ In order to avoid tearing off the plate at an edge, the distance from the centre of the rivet hole to the nearest edge of the plate (i.e. margin) should be (where

*d*= Diameter of rivet hole in mm)

d

1.5 d

2 d

2.5 d

⇒ Young's modulus may be defined as the ratio of.

linear stress to lateral strain

lateral strain to linear strain

linear stress to linear strain

shear stress to shear strain

⇒ A beam supported on more than two supports is called

simply supported beam

fixed beam

overhanging beam

continuous beam

⇒ When a thin cvlindrical shell is subjected to an internal pressure, the volumetric strain is (where ε

_{1}= Hoop strain, and ε

_{2}= Longitudinal strain)

2Îµ1 - Îµ2

2Îµ1 + Îµ2

2Îµ2 - Îµ1

2Îµ2 + Îµ1

⇒ A load which acts at a point on a beam is not called uniformly distributed load.

Agree

Disagree

True

False

⇒ The energy absorbed in a body, when it is strained within the elastic limits, is known as

strain energy

resilience

proof resilience

modulus of resilience

⇒ Which of the following statement is correct?

The stress is the pressure per unit area.

The strain is expressed in mm.

Hook's law holds good upto the breaking point.

Stress is directly proportional to strain within elastic limit.

⇒ If a material expands freely due to heating it will develop

thermal stresses

tensile stress

bending

compressive stress

⇒ The ratio of shear modulus to the modulus of elasticity for a Poisson's ratio of 0.4 will be.

5/7

7/5

5/14

14/5

⇒ The buckling load for a given material depends on

slenderness ratio and area of cross-section

Poisson's ratio and modulus of elasticity

slenderness ratio and modulus of elasticity

slenderness ratio, area of cross-section and modulus of elasticity

⇒ Which of the following statement is wrong?

The deformation of the bar per unit length in the direction of the force is called linear strain.

The Poisson's ratio is the ratio of lateral strain to the linear strain.

The ratio of change in volume to the original volume is called volumetric strain.

The bulk modulus is the ratio of linear stress to the linear strain.

⇒ A masonry dam may fail due to?

tension in the masonry of the dam and its base

overturning of the dam

crushing of masonry at the base of the dam

any one of the above

⇒ For riveting, the size of hole drilled in plates is __________ shank diameter of rivet.

equal to

less than

greater than

none of these

⇒ A riveted joint in which the number otrivets decrease from innermost to outer most row is called

chain riveted joint

diamond riveted joint

cross-cross riveted joint

zig-zag riveted joint

⇒ When a rectangular beam is loaded longitudinally, the shear force develops on the top layer.

Agree

Disagree

True

False

⇒ In a beam where shear force changes sign, the bending moment will be.

zero

minimum

maximum

infinity

⇒ In calculating the strength of a riveted joint in tearing, shearing and crushing, the

actual diameter of rivet is used

actual diameter of hole drilled for rivet is used

mean diameter of hole drilled and rivet is used

smaller of the rivet diameter and hole diameter is used

⇒ On one side of a neutral axis of a beam, there is a tensile stress and on the other side of the beam there is a compressive stress.

Agree

Disagree

Yes

No

⇒ When a body is subjected to a direct tensile stress (σ) in one plane, then tangential or shear stress on an oblique section of the body inclined at an angle θ to the normal of the section is

Ïƒ sin 2Î¸

Ïƒ cos 2Î¸

Ïƒ/2 sin 2Î¸

Ïƒ/2 cos 2Î¸

⇒ In a belt drive, the pulley diameter is doubled, the belt tension and pulley width remaining same. The changes required in key will be

increase key length

increase key depth

increase key width

double all the dimensions

⇒ The steel bars in a reinforced cement concrete beam are embedded __________ of the beam.

in the centre

near the bottom

near the top

at any position

⇒ In a thick cylindrical shell subjected to an internal pressure (

*p*), the maximum radial stress at the inner surface of the shell is.

zero

p (tensile)

-p (compressive)

2p (tensile)

⇒ For steel, the ultimate strength in shear as compared to in tension is nearly

same

half

one-third

two-third