Question is ⇒ The bandwidth required for amplitude modulation is, Options are ⇒ (A) half the frequency of modulating signal, (B) equal to the frequency of modulating signal, (C) twice the frequency of modulating signal, (D) four times the frequency of modulating signal, (E) , Leave your comments or Download question paper.

Question is ⇒ The bandwidth required for amplitude modulation is, Options are ⇒ (A) half the frequency of modulating signal, (B) equal to the frequency of modulating signal, (C) twice the frequency of modulating signal, (D) four times the frequency of modulating signal, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The bandwidth required for amplitude modulation is
A.	half the frequency of modulating signal [Wrong Answer]
B.	equal to the frequency of modulating signal [Wrong Answer]
C.	twice the frequency of modulating signal [Correct Answer]
D.	four times the frequency of modulating signal [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The resonance frequency is
ω_r = a
ω_r = b
ω_r = k
ω_r = ba

⇒

Assertion (A): The circuit of figure thyristor will conduct for 180° during positive half cycle if it is continuously fir
Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Antenna beamwidth is
measure of directivity
measure of angle
measure of radiation pattern
measure of power pattern

⇒ In a pulsed RADAR typical value of pulse duration and pulse frequency respectively are
1 μs and 50 Hz
1 μs and 500 Hz
4 μs and 50 Hz
4 μs and 500 Hz

⇒ Two wires A and B have the same cross-section area and are made of the same material. R_A = 600 Ω and R_B = 100 Ω. The number of times A is longer than B is
6
2
4
5

⇒

Assertion (A): Millman's theorem helps in replacing a number of current sources in parallel by a single current source.

Reason (R): Maximum power transfer theorem is applicable only for dc, circuits.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a pulsed RADAR, the transmitter is connected to the antenna
during pulse interval
during interval between pulses
all the time
only during a fraction of pulse interval

⇒

Assertion (A): The behaviour of FET is similar to that of a pentode.

Reason (R): FETs and vacuum triode are voltage controlled devices.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ E_G for silicon is 1.12 eV and that for germanium is 0.72 eV. Therefore it can be concluded that
more number of electron-hole pairs will be generated in silicon than in germanium at room temperature
less number of electron hole pairs will be generated in silicon than in germanium at room temperature
equal number of electron-hole pairs will be generated in both at lower temperatures
equal number of electron-hole pairs will be generated in both at higher temperatures

⇒ Determine the transistor capacitance of a diffused junction varicap diode of a reverse potential of 4.2 V if C(0) = 80 pf and V_T = 0.7 V
42 pf
153.03 pf
13.33 pf
Data inadequate

⇒ Which one is correct?
Sky wave propagation (2 to 30 MHz)
Space wave propagation (> 30 MHz)
Tropospheric propagation (> 300 MHz)
All of the above

⇒ The resistance of a bulb at the time of full brightness is 1200 Ω. Then the resistance at room temperature is about
1200 Ω
120 Ω
600 Ω
10 Ω

⇒ The application of gate signal decreases the break over voltage of on SCR.
TRUE
FALSE

⇒ In the given figure assume that initially Q = 1 with Clock Pulses being given, the subsequent states of Q wil
1, 0, 1, 0, 1......
0, 0, 0, 0, 0......
1, 1, 1, 1, 1......
0, 1, 0, 1, 0......

⇒ A parallel resonant circuit can be used
as a high impedance
to reject a small band of frequencies
both (a) and (b)
to amplify certain frequencies

⇒ (29)₁₃ ÷ (29)₁₂ x (29)_x = (23)₁₆ Find x
11
12
13
16

⇒ A 4 : 1 multiplexer requires __________ data select line.
1
2
3
4

⇒ Consider the followings statements: A multiplier

selects one of the several inputs and steers it to the output
routes the data from a single input to many outputs
converts parallel data into serial data
is a combinational circuit

On the above statements which are correct?
1, 2, 4
2, 3, 4
1, 3, 4
1, 2, 3

⇒ The minimum number of 2 input NAND gates required to implement Boolean function A B C is A, B, C are available is
2
3
5
6

⇒ Holes and electrons move in opposite directions.
TRUE
FALSE

⇒ In amplitude modulation, the magnitude of side bands is
ma/2 times the carrier amplitude, E_c
ma times the carrier amplitude, E_c
2ma times the carrier amplitude, E_c
4ma times the carrier amplitude, E_c

⇒ Consider the following stateme
1, 2, 3
1, 3, 4
2, 3, 4
1, 2, 4

⇒ Consider the following instruction of 8085 μp :

MOV M, A
AODC
MVI A, FF
CMP M

Which of these cause change in the status of flag(s)?
1 and 2
1, 2 and 3
3 and 4
2 and 4

⇒ The first contribution to logic was made by
George Boole
Copernicus
Aristotle
Shannon

⇒ The use of SSB
halves the bandwidth required for transmission
does not affect the bandwidth for transmission
decreases the bandwidth required for transmission by 25%
decreases the bandwidth required for transmission by 66.6%

⇒ The multivibrator circuit that has a typical application of converting sinusoidal input into a square wave output is
emitter coupled binary
Schmitt trigger
monoshot multivibrator
free-running multivibrator

⇒

Assertion (A): The output of a NOR gate is equal to the complement of OR of input variables.

Reason (R): A XOR gate is a universal gate.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ If ROC of x[n] is R₁ then ROC of aⁿ x[n] is
R₁a
R₁/a
a/R₁
R₁ + a

⇒ The transistor specification number 2N refers to
triac
diac
junction transistor
FET with one gate

⇒ The multiplication time for 10-bit numbers with 1 MHz clock will be
32 μ sec
20 μ sec
21 μ sec
22 μ sec