Question is ⇒ The automobile chassis consists of the engine, frame, power train, wheels, steering and .............., Options are ⇒ (A) The doors, (B) Luggage boot, (C) Wind shield, (D) Braking system, (E) , Leave your comments or Download question paper.

Question is ⇒ The automobile chassis consists of the engine, frame, power train, wheels, steering and .............., Options are ⇒ (A) The doors, (B) Luggage boot, (C) Wind shield, (D) Braking system, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The automobile chassis consists of the engine, frame, power train, wheels, steering and ..............
A.	The doors [Wrong Answer]
B.	Luggage boot [Wrong Answer]
C.	Wind shield [Wrong Answer]
D.	Braking system [Correct Answer]
View Answer 6 -9 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The three forward speed and the reverse transmission consists of three shafts and
Three gears
Five gears
Eight gears
Ten gears

⇒ The automobile transmission is removed from the car by taking it out
From under car
Through driving compartment
Through engine compartment

⇒ The power developed inside the engine cylinder is called
IHP
FHP
BHP

⇒ In jeeps we use
Mechanical brakes
Hydraulic brakes
Air brakes

⇒ The pipes used in diesel engines from pump to nozzle is made up of
PVC
Rubber
Steel
Copper

⇒ In coil spring type of clutch the cover is separated by
Removing three screws or nuts
Unhooking three retainer springs
Removing wire coil springs
Detaching three lever springs

⇒ The brake shoes are curved to conform to the inner diameter of the
Tyre
Wheel
Pedal
Brake drum

⇒ Floating axles are classified on the basis of
The amount of torque transmitted
Depending upon their location whether at front or rear
Depending on the nature of forces like torsional vertical and lateral to which they are subjected
Purely on the basis of type and number of bearings used at the work

⇒ In the transmission system, the provision of slip joints allows a change in the
Angle of drive
Length of shaft
Speed of rotation

⇒ The purpose of the fluid coupling is to act as a
Synchronizing device
Automatic gear changer
Flexible power-transmitting coupling

⇒ The ease with which a liquid changes to a vapour is called its
Vapourability
Boiling point
Viscosity
Volatility

⇒ When an automobile takes a tum to avoid the skidding and over turning
Each wheel will roll independently
Front two wheels will have a common centre during a turning
All the 4 wheels will roll on arcs having a common centre

⇒ The universal joint permits a change in the
Length of the shaft
Speed of rotation
Angle of drive

⇒ The type of air cycle used in diesel engine is called
Otto cycle
Carnot cycle
Diesel cycle
Rankine cycle

⇒ The most popular drive at the drive axle for the passenger car is
Straight bevel gear
Spiral bevel gear
Worm gear drive
Hypoid drive

⇒ Connecting rods are generally of the following from
Forged round section steel
Cast steel triangular section
Forged square section steel
Forged I section steel

⇒ Gudgeon pins or piston pins are made by
Piston material itself
Cork
Cast iron
Hardened and ground steel

⇒ In the differential, to correct for heavy flank contact on the drive gear teeth, it is necessary to move the
Drive pinion in
Drive pinion out
Drive gear out and then adjust back lash

⇒ The amount of air fuel mixture taken in by the engine on the suction stroke is a measure of the engine's
Compression ratio
Volumetric efficiency
Clearance volume

⇒ The fuel injected when pressure in the cylinder reaches the point ........... on the curve
1
2
3
4

⇒ A humming noise in the differential is often caused by improper tooth contact between the
Drive pinion & ring gear
Axle and side gear
Pinion and side gears

⇒ The crankcase scavenging the the crankcase or underside of the piston acts as
An air compressor
A blower
A ventilator
A breather

⇒ X - member of a car frame ensures improved
Resistance to side force due to transverse wind load
Bending strength of side members
Resistance to vertical shock loads acting simultaneously on both front wheels
Resistance of weaving and torsional strength of front end of frame

⇒ If two meshing gears have 4:1 gear ratio and the smaller gear has 12 teeth, the large gear will have
12 teeth
24 teeth
36 teeth
48 teeth

⇒ Pressing down on clutch pedal causes the release levers to move the pressure plate away from
Friction disc
Clutch cover
Pressure plate baffle
Throw out bearing

⇒ For petrol engines the nominal compression ratio will vary between
1 to 2:1
18 to 21:1
1 to 5:1
7.5 to 8.5:1

⇒ The ratio of the cylinder volume at BDC and the clearance volume is called
Clearance ratio
Volumetric ratio
Compression ratio

⇒ In the vacuum suspended system, the brakes are applied when
Atmospheric pressure is applied to one side of the diaphragm
Vacuum is applied to both sides of diaphragm
Atmospheric pressure is applied to both sides of the diaphragm

⇒ In the modern differential, the type of gearing used for the drive pinion and ring gear is
Spur
Spiral bevel
Hypoid

⇒ If we know the engine speed, bore, stroke, number of cylinders and m.e.p in the cylinders, we can calculate
FHP
IHP
BHP