Question is ⇒ The 8085 microprocessor is interrupted while executing MOV instruction at location 0210 H. What is the location at which contents of register D are stored, Options are ⇒ (A) 054 CH, (B) 054 DH, (C) 054 EH, (D) 054 FH, (E) , Leave your comments or Download question paper.

Question is ⇒ The 8085 microprocessor is interrupted while executing MOV instruction at location 0210 H. What is the location at which contents of register D are stored, Options are ⇒ (A) 054 CH, (B) 054 DH, (C) 054 EH, (D) 054 FH, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The 8085 microprocessor is interrupted while executing MOV instruction at location 0210 H. What is the location at which contents of register D are stored
A.	054 CH [Wrong Answer]
B.	054 DH [Wrong Answer]
C.	054 EH [Wrong Answer]
D.	054 FH [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following instructions in 8085 does not belong to data transfer group?
L X I rp, data 16
MOV M, r
MVIM, data
ADC M

⇒ Consider the following about 'arrays' in C

An array is a collection of similar elements.
An array can not have 10 numbers 5 of which are ints and 5 are floats.
An array can have ints and chars in the same array.

Which of the above are correct?
All
1 and 2 only
1 and 3 only
2 and 3 only

⇒ The number of storage classes in C is
2
3
4
6

⇒ A ring counter with 5 flip flops will have
5 states
10 states
32 states
infinite states

⇒ A piece of iron is placed in a magnetic field
the magnetic field will not be affected
the magnetic lines of force will bend to pass through the piece
the magnetic lines of force will bend away from the piece
any of the above depending on type of iron

⇒ When a potential is applied across an intrinsic semiconductor, holes flow
towards positive terminal
away from positive terminal
in the external circuit only
none of the above

⇒ Top loading in an antenna increases
effective height
beam width
input capacitance
bandwidth

⇒ In a FM waveform, the side bands are spaced at intervals equal to
four times the modulating frequency
twice the modulating frequency
half the modulating frequency
modulating frequency

⇒ Which one of the following is loaded in the main memory by the bootstrap loader?
System data
User program
BIOS
Part of DOS

⇒ In figure, i(0^-) and v(0^-) are zero. The switch is closed at t = 0, i(0⁺) and (∞)
3 A and 1.5 A
1.5 A and zero
3 A and zero
1.5 A and 3 A

⇒ While forming Routh's array, the situation of a row of zeros indicates that the system
has symmetrically located roots
is not sensitive to variations in gain
is stable
is unstable

⇒ A silicon wafer has 100 nm of oxide it and is inserted in a furnace at a temperature above 1000°C for further oxidation in dry oxygen. The oxidation rate
is independent of current oxide thickness and temperature
is independent of current oxide thickness but depends on temperature
slows down as the oxide grows
is zero as the existing oxide prevents further oxidation

⇒ Consider the transmission line of length 37.5 cm, which is terminated into zero resistance. This line is being exited by a source of 1 GHz which has an internal impedance of 50 Ω. What is the input impedance of the line as seen by the source?
50 Ω
Zero Ω
100 Ω
Infinite Ω

⇒ If f_s be the signal frequency and f_i be the intermediate frequency then image frequency is given by
f_s + f_i
f_s ± f_i
f_s ± 2f_i
f_s + 2f_i

⇒ If the target cross-section is changing, the best scanning system for accurate tracking is
lobe switching
monopulse
sequential lobing
conical scanning

⇒ The gate lead, in a thyristor is welded to :
p layer to which anode is connected
n layer nearest to the anode terminal
p layer nearest to the cathode terminal
outside n layer

⇒ If a two port network is represented by an equivalent T network the admittance of series arm in term of ABCD parameter is equal to
C
1/C
(A - 1)/B
1/B

⇒ Consider the following statements as regards SAW filter

The centre frequency is determined by the pitch of IDT comb shaped electrodes
The response can be modified shaping the overlap of comb electrodes
The response is maximum when acoustic wave has its wavelength equal to pitch
When a number of identical electrodes are arranged at the same pitch, the frequency characteristics of the filter is expressed by (sin x)/x

Which of the above statements are correct?
1, 2, 3, 4
1, 2, 3 only
1, 2, 4 only
2, 3, 4 only

⇒ In a JK flip flop output Q_n = 1 and it does not change when clock pulse is applied. The possible combination of J_n and K_n is (X denotes don't care)
X and 0
X and 1
0 and X
1 and X

⇒ In a strain measuring device using a strain gauge, the output quantity is
voltage
resistance
impedance
either (a) or (b)

⇒ A system with input x[n] and output y[n] is given as y[n] = (sin 5/6 pn) x(n) The system is
linear, stable and invertible
non-linear, stable and non-invertible
linear stable, non invertible
linear, unstable, invertible

⇒ A plot of modulation index vs carrier amplitude yields a
horizontal line
vertical line
parabola
hyperbola

⇒ Which of the following does not show non-linear V-I characteristics?
Schottky diode
Tunnel diode
Thermister, at a fixed temperature
p-n junction diode

⇒ The chip 8254 is a 40 pin programmable interval timer. The number of its independent 16 bit counters is
2
3
4
5

⇒ Counterpoise is used in coils having
high resistivity
low resistivity
medium resistivity
both (b) and (c)

⇒ When a 10 K, 10%, 1/4 Ω resistor is connected in series with a 12 K, ± 1%, 1/4 Ω resistor, the resulting combination has the following specifications
22 K, ± 11%, 1/2 Ω
22 K, ± 5.5%, 1/2 Ω
22 K, ± 5.5%, 1/8 Ω
none of these

⇒ In a computer the instructions, data, intermediate and final results during processing are held in ALU.
TRUE
FALSE

⇒ Data can be changed from spatial code to temporal code and vice-versa by using
ADC and DAC
shift Register
synchronous counter
timers

⇒ A dc network has 3 independent nodes and 4 loops. In total analysis, the number of equations is
4
3
2
1

⇒ For a quadratic factor in transfer function the phase angle is not a function of damping factor.
TRUE
FALSE