Question is ⇒ 'Rotate instruction' in microprocessor belongs to, Options are ⇒ (A) data transfer group, (B) arithmetic group, (C) logic group, (D) branch group, (E) , Leave your comments or Download question paper.

Question is ⇒ 'Rotate instruction' in microprocessor belongs to, Options are ⇒ (A) data transfer group, (B) arithmetic group, (C) logic group, (D) branch group, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	'Rotate instruction' in microprocessor belongs to
A.	data transfer group [Wrong Answer]
B.	arithmetic group [Wrong Answer]
C.	logic group [Correct Answer]
D.	branch group [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A 4 bit ripple counter uses flip flops with propagation delay of 50 ns each. The maximum clock frequency which can be used is
5 MHz
10 MHz
20 MHz
25 MHz

⇒ In op-amp integrating amplifier the input is feed to
inverting input
non-inverting input
both inverting and non-inverting input
either inverting or non-inverting input

⇒ In an integral controller
the output is proportional to input
the rate of change of output is proportional to input
the output is proportional to rate of change of input
none of the above

⇒ The main feature of a parametric amplifier is
low noise
very high gain
broad bandwidth
both (b) and (c)

⇒ The power input and output in a device are 3650 W and 3385 W with each reading in doubt by ± 10 W. The percentage uncertainty in losses is
± 7.55%
± 3.77%
± 11.32%
± 15.09%

⇒ The coil of a moving iron instrument has a resistance of 500 Ω and an inductance of 1 H. It reads 250 V when a 250 V dc is applied. If series resistance is 2000 Ω, its reading when fed by 250 V, 50 Hz ac will be
260 V
252 V
250 V
248 V

⇒ If the iron core of a coil is removed so that it becomes an air cored coil, its inductance
will increase
will decrease
will remain the same
may increase or decrease

⇒ A system has its two poles on the negative real axis and one pair of poles lies on jω axis. The system is
stable
unstable
limitedly stable
either (a) or (c)

⇒ Which one of the following is an indirect way of generating FM?
Armstrong modulator
Varactor diode modulator
Reactance FET modulator
Reactance bipolar transistor modulator

⇒ Fourier transform and F(jω) of a signal f(t) has the property
F(jω) = F(-jω)
F(jω) = -F(-jω)
F(jω) = F^*(jω)
F(jω) = -F^*(-jω)

⇒

Assertion (A): The resistivity of intrinsic semiconductor decreases with increase in temperature.

Reason (R): The forbidden gap decreases with increase in temperature.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The Z parameters Z₁₁ and Z₂₁ for the 2-port network in the fig
Z₁₁ = - 6/₁₁Ω; Z₂₁ = 16/₁₁Ω
Z₁₁ = 6/₁₁Ω; Z₂₁ = 4/₁₁Ω
Z₁₁ = 6/₁₁Ω; Z₂₁ = - 16/₁₁Ω
Z₁₁ = 4/₁₁Ω; Z₂₁ = 4/₁₁Ω

⇒ What will be BCD number when the output is 0.37 V?
110111
10110111
11001000
1001000

⇒ Consider the following circuit configuration

common Emitter
common Base
emitter follower
emitter follower using Darlington pair.

The correct sequence in increasing order of I/P impedance of these configuration:
2, 1, 4, 3
1, 2, 4, 3
2, 1, 3, 4
1, 2, 3, 4

⇒ Consider the following statements

An assembler is a program having assembly language program as input and machine language program as output.
A macro assembler is an assembler with additional macro facilities.
A cross assembler for a μP X is an assembler which executes on source microcomputer with a different CPU than X bit generates code for X.
Assemblers generally do not provide macro facilities.

Of the above statement
All are correct
only 1, 2, 3 are correct
only 1, 2, 4 are correct
only 1, 3, 4 are correct

⇒ A rhombic antenna is a
resonant antenna
non-resonant antenna
coupled antenna
none of the above

⇒ To draw dc equivalent circuit for a CE amplifier circuit we should
Reduce all ac sources to zero
Open all capacitors
Reduce all ac sources to zero and open all capacitors
Reduce all ac sources to zero and short all capacitors

⇒ In figure the current through resist
is always equal to 130 mA
may vary between 130 mA and 10 mA
may vary between 65 mA and 10 mA
is always equal to 65 mA

⇒ Which of the following is not a valid variable name in C?
p_ce1
1p_ce
p1_ce
p _ced

⇒ On which of the following effect do thermocouples work?
Thomson effect
Seeback effect
Peltier effect
Joule effect

⇒ A dc network has 3 independent nodes and 4 loops. In total analysis, the number of equations is
4
3
2
1

⇒ If X(z) = (1 - az^-1)^-1 and |a| < |z|, the initial value x₀ = 0
TRUE
FALSE

⇒ For a resistance of about 15 kΩ operating in a frequency range of a few MHz, the noise voltage is in the range of
a few μV
about 100 μV
a few μV
a few volts

⇒ Which of the following noise sources is different from others?
Cosmic
Solar
Atmospheric
Galactic

⇒ Cross talk is due to reception of portions of a signal from one channel into another.
TRUE
FALSE

⇒ The point P in the following figure is stock at 1. The output f wil
ABC
A
AB C
A

⇒ Two discrete time systems with impulse responses h₁[n] = δ[n - 1] and h₂[n] = δ[n - 2] are connected in cascade. The overall impulse response of the cascaded system is
δ[n - 1] + δ[n - 2]
δ[n - 4]
δ[n - 3]
δ[n - 1] + δ[n - 2]

⇒ Z₀ = (Z_oc Z_sc)^0.5
TRUE
FALSE

⇒

Assertion (A): In an n-p-n transistor as the electrons enter the collector region, they are accelerated towards the collector terminal.

Reason (R): Emitter base junction in BJT is forward biased.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒

Match the following:

	List I		List II
A.	R = 0	1.	Undamped oscillation
B.	R < 2 L/C	2.	Damped oscillation
C.	R = 2 L/C	3.	Critically damped response
D.	R > 2 L/C	4.	Non-oscillatory response.

A-1, B-2, C-3, D-4
A-1, B-4, C-3, D-2
A-3, B-2, C-1, D-4
A-3, B-4, C-1, D-2