Question is ⇒ Propellers are, Options are ⇒ (A) axial flow mixers., (B) low speed impeller., (C) used for mixingliquids of high viscosity., (D) radial flow mixers., (E) , Leave your comments or Download question paper.

Question is ⇒ Propellers are, Options are ⇒ (A) axial flow mixers., (B) low speed impeller., (C) used for mixingliquids of high viscosity., (D) radial flow mixers., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Propellers are
A.	axial flow mixers. [Correct Answer]
B.	low speed impeller. [Wrong Answer]
C.	used for mixingliquids of high viscosity. [Wrong Answer]
D.	radial flow mixers. [Wrong Answer]
View Answer 25 -12 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type.
axial
radial
mixed
none of these

⇒ In a dry packed bed, the pressure drop will be changed by increasing the flow rate as
V^1.8
V^-0.8
V
V^-1

⇒ Froude number is the ratio of
shear stress to gravitational stress.
drag stress to shear stress.
inertial stress to shear stress.
inertial stress to gravitational stress.

⇒ Dean number is concerned with the
fluid-particle interaction.
fluid flow through helical pipes.
power consumption in agitated vessels.
psychrometry.

⇒ Dimension of kinematic viscosity is
MLT^-1
L² . T^-1
L²T
L² . T^-2

⇒ Which of the following is the most common pump for pumping either raw sewage or sludge ?
Electromagnetic pump
Centrifugal pump
Reciprocating pump
Gear pump

⇒ Flow measurement in an open channel is done by a/an
venturimeter
orificemeter
weir
rotameter

⇒ Which of the following is most prone to pulsating discharge flow ?
Centrifugal pump
Reciprocating pump
Gear pump
Axial flow pump

⇒ Select the correct practical example of steady non-uniform flow.
Motion of water around a ship in a lake.
Motion of river around bridge piers.
Steadily decreasing flow through a reducing section.
Steadily increasing flow through a pipe.

⇒ Momentum transfer in laminar flow of fluids results due to the
viscosity
density
velocity gradient
none of these

⇒ An ideal fluid is
non-viscous
incompressible
both (a) & (b)
neither (a) & (b)

⇒ One dimensional fluid flow implies the
flow in straight lines only.
uniform flow.
steady uniform flow.
flow in which transverse components are zero.

⇒ To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump.
reciprocating
centrifugal
volute
rotary vacuum

⇒ The ratio of wall drag to total drag in the Stoke's law range is
0.5
1
42738
42769

⇒ The unit of dynamic viscosity in SI unit is
kg/m . sec
N/m²
m² /sec.
m/N. sec.

⇒ Steady non-uniform flow is exemplified by flow through a/an
long pipe at constant rate.
long pipe at decreasing rate.
expanding tube at increasing rate.
expanding tube at constant rate.

⇒ Non-colloidal solution is an example of the __________ fluid.
non-Newtonion
Newtonion
dilatent
pseudoplastic

⇒ Capacity of a hydraulic accumulator is defined in terms of maximum
amount of energy stored.
flow rate through accumulator.
rate of falling of ram.
volume available in the cylinder.

⇒ Schedule number of a pipe, which is a measure of its wall thickness, is given by
1000 P'/S
100 P'/S
1000 S/P'
10000 P'/S

⇒ Mass velocity in case of steady flow and through a constant cross-section conduit is independent of the
temperature
pressure
both (a) & (b)
neither (a) nor (b)

⇒ In a fluidised bed reactor
temperature gradients are very high.
temperature is more or less uniform.
hot spots are formed.
segregation of the solids occurs.

⇒ With increase in the temperature, viscosity of a liquid
increases
decreases
remains constant
may increase or decrease; depends on the liquid

⇒ Pick out the wrong statement:
Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer.
Blowers develop a maximum pressure of 2 atmospheres.
Friction losses in pipe fittings are generally expressed in terms of velocity heads.
Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number.

⇒ For a particle settling in water at its terminal settling velocity, which of the following is true ?
Buoyancy = weight + drag
Weight = buoyancy + drag
Drag = buoyancy + weight
Drag = weight

⇒ The dimension of dynamic viscosity is
ML^-1T^-1
L²T^-1
LT^-2
ML^-1T^-2

⇒ The Prandtl pitot tube measures the
velocity at a point in the flow.
pressure at a point.
average flow velocity.
pressure difference in pipe flow.

⇒ If more than two branches of pipes are to be connected at the same point, then use a/an
elbow
union
tee
none of these.

⇒ Pump used for the transportation of molten sodium in a fast breader reactor is a/an __________ pump.
reciprocating
plunger
electromagnetic
gear

⇒ Centre of pressure of a plane surface of arbitrary shape immersed vertically in a static mass of fluid
lies above the centroid of the plane surface.
is independent of the specific weight of the fluid.
is different for different fluids.
is at the centroid of the plane surface.

⇒ Pick out the wrong statement:
The vacuum pressure is always the negative gauge pressure.
The pressure of the liquid measured by a piezometer tube is the gauge pressure.
Manometric liquid should have high surface tension.
The point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity.