Question is ⇒ Power factor of electric bulb is, Options are ⇒ (A) Zero, (B) Lagging, (C) Leading, (D) Unity, (E) , Leave your comments or Download question paper.

Question is ⇒ Power factor of electric bulb is, Options are ⇒ (A) Zero, (B) Lagging, (C) Leading, (D) Unity, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Power factor of electric bulb is
A.	Zero [Wrong Answer]
B.	Lagging [Wrong Answer]
C.	Leading [Wrong Answer]
D.	Unity [Correct Answer]
View Answer 15 -17 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is
70.7 A
141.4A
150A
282.8 A

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees
90
60
45
30

⇒ Form factor is the ratio of
Average value/r.m.s. value
Average value/peak value
r.m.s. value/average value
r.m.s. value/peak value

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates
Low efficiency
High power factor
Unity power factor
Maximum Load current

⇒ The value of operator j2 is equal to
Zero
+1
-1
√-1

⇒ If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be
0.001 S
0.1 S
10 S
100 S

⇒ In the R - L - C containing R = 4.5ω L = 0.06 H,C = 0.6 µF the power factor will be
Zero
Lagging
Leading
Unity

⇒ For a sine wave with peak value E_max the average value is
0.636 E_max
0.707 E_max
0.434 E_max
1.414 E_max

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?
0.5A
1.5 A
2A
3A

⇒ In a pure resistive circuit
Current lags behind the voltage by 90°
Current leads the voltage by 90°
Current can lead or lag the voltage by 90°
Current is in phase with the voltage

⇒ In a series resonant circuit, the impedance of the circuit is
Maximum
Minimum
Zero
Infinite

⇒ A network is said to be non-linear if it does not satisfy
Homogeneity condition
Superposition condition
Both (A) and (B)
Associative condition

⇒ The capacitors for power factor correction are rated in terms of
Voltage
VA
kW
kVAR

⇒ Inductance affects the direct current flow
Only at the time of turning off
Only at the time of turning on
At the time of turning on and off
At all the time of operation

⇒ Power factor of electric bulb is
Zero
Lagging
Leading
Unity

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.
Low
Very low
High
Very high

⇒ For a sine wave with peak value I_max the r.m.s. value is
0.5 I_max
0.707 I_max
0.9 I_max
1.414 I_max

⇒ The shunt element in a band pass filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ The r.m.s. value of pure cosine function is
0.5 of peak value
0.707 of peak value
Same as peak value
Zero

⇒ At half power points of a resonance curve, the current is____ times the maximum current.
1/2
1/ √2
√2
2

⇒ Poor power factor results in all of the following EXCEPT.
Overloading of transformers
Overloading of altemators
Reduction in power losses
Reduction in load handling capacity of electrical system

⇒ A coil with large distributed capacitance has a
High resonant frequency
Low resonant frequency
Low quality factor
Low resistance

⇒ In A.C. circuit the power curve is a sine wave having
Double the frequency of voltage
Same frequency as that of voltage
Half the frequency of the voltage
None of these

⇒ For 200 V r.m.s. value triangular wave, the peak voltage will be
200 V
222 V
282 V
346 V

⇒ The power is measured in terms of decibles in case of
Electronic equipment
Transformers
Current transformers
Auto-transformers

⇒ Which of the following is not a non-linear element ?
Transistor
Heater coil
Diode
Electric arc with unlike electrodes

⇒ The power factor of incandescent bulb is
0.8 lagging
0.8 leading
Unity
Zero

⇒ The series element of a band stop filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ The best place to install a capacitor is
Very near to inductive load
Across the terminals of the inductive load
Far away from the inductive load
Any where

⇒ A heater is rated as 230 V, 10 KW, AC. The value 230 V refers t
Average voltage
r.m.s. voltage
Peak voltage
None of these