Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Match the following:
| ||||||||||||||||

A. | A-1, B-2, C-3 [Wrong Answer] | ||||||||||||||||

B. | A-3, B-1, C-2 [Correct Answer] | ||||||||||||||||

C. | A-2, B-1, C-3 [Wrong Answer] | ||||||||||||||||

D. | A-3, B-2, C-1 [Wrong Answer] | ||||||||||||||||

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A 2 bit BCD D/A converter is a weighted resistor type with E

_{R}= 1V, R = 1 MΩ and R

*= 10KΩ then Resolution in percent and volt is __________ .*

_{f}1%, 1 mv

10%, 10 mv

10%, 1 mv

1%, 10 mv

⇒ What is the effect of cut in voltage on the wave form of output as compared to input in a semiconductor diode?

The duration of output waveform is less than 180°

Output voltage is less than input voltage

Output voltage is more than input voltage

Both (a) and (b)

⇒ In an electrochemical process the mass of material deposited at an electrode is proportional to

time for which current is passed

magnitude of current

electric charge through the electrolyte

none of the above

⇒ Zener diode is invariably used with

forward bias

reverse bias

either (a) or (b)

zero bias

⇒ The first critical frequency nearest the origin of the complex frequency plane for an RL driving point impedance will be

a zero in left half plane

a zero in right half plane

a pole in left half plane

a pole or zero in left half plane

⇒

Match the following:

List I (Devices) | List II (characteristic) | ||
---|---|---|---|

A. | BJT | 1. | Voltage controlled negative resistance |

B. | MOSFET | 2. | High current gain |

C. | Tunnel diode | 3. | Voltage regulation |

D. | Zener diode | 4. | High input impedance |

A-1, B-4, C-2, D-3

A-2, B-4, C-1, D-3

A-2, B-3, C-1, D-4

A-1, B-3, C-2, D-4

⇒ A zero mean white Gaussian noise is passed through an ideal low pass filter of bandwidth 10 kHz. The output of the samples so obtained would be

correlated

statistically independent

uncorrelated

orthogonal

⇒ A(A + B) =

A

A B

AB

AB

⇒ If air pressure in a rectangular waveguide is increased the maximum power handling capacity

is decreased

is increased

remains the same

may increase or decrease depending on pressure

⇒ An encoder converts decimal numbers to binary and other codes.

TRUE

FALSE

⇒ The dynamic characteristics of capacitive transducer are similar to those of

LP filter

HP filter

notch filter

band stop filter

⇒ The orbital period of a geostationary communication satellite is

12 hours

24 hours

36 hours

48 hours

⇒ If input frequency is 50 Hz, the frequency of output wave in a full wave diode rectifier circuit is

25 Hz

50 Hz

100 Hz

200 Hz

⇒ The electrical requirement on wall thickness of rectangular wave guide is

wall thickness is more than skin depth

wall thickness is less than skin depth

wall thickness is equal to skin depth

either (b) or (c)

⇒ The relaxation time of electrons in a metal is of the order of

10

^{-6}secs

10

^{-10}secs

10

^{-14}secs

10

^{-20}secs

⇒

**Assertion (A):** In intrinsic semiconductors, the charge concentration increases with temperature.

**Reason (R):** At higher temperatures, the forbidden energy gap in semiconductors is lower.

Both A and R are true and R is correct explanation of A

Both A and R are true but R is not a correct explanation of A

A is true but R is false

A is false but R is true

⇒ The frame of electric motor is connected to three plates having earthing resistance of 10 Ω, 20 Ω and 30 Ω respectively. The materials of the three plates are copper, aluminium and iron respectively. The percentage of energy dissipated by 10 Ω earthing plate

is more than 50% of total energy

is less than 50% of total energy

depends on the materials of the three plates

may be more or less than 50% of total energy

⇒ The material used for fuse must have

low melting point and low specific resistance

low melting point and high specific resistance

high melting point and low specific resistance

none

⇒ If 137 + 276 = 435 how much is 731 + 672?

534

1403

1623

1513

⇒ A single phase series converter is used for

high voltage output

high current output

high voltage and high current output

improving the circuit efficiency

⇒ In a 7 segment LED display, the minimum number of segments is activated when the input decimal number is

0

1

2

3

⇒ In a single phase half wave converter feeding resistive load and full wave converter (M - 2 connection) feeding a resistive load the circuit conditions are similar. The firing angle is a. Then the waveshapes of voltages across thyristors

are similar

are not similar

may be similar or dissimilar

are similar only for some values of a

⇒ In a 4 bit full adder how many half adders and OR gates are required

8 and 4

7 and 4

7 and 3

8 and 3

⇒ The start of modern computer age was started by the event

development of disc drive

development of transistor

development of Hollerith code

design of EVIAC computer

⇒ The difference between sequential and combinational circuits is

Combinational circuits store bits

Combinational circuits have memory

Sequential circuits store bits

Sequential circuits have memory

⇒ A universal RLC bridge uses

Maxwell bridge for measurement of inductance and De Sauty's bridge for measurement of capacitance

Maxwell's bridge for measurement of inductance and modified De Sauty bridge for measurement of capacitance

Maxwell Wien bridge for measurement of inductance and modified De Sauty bridge for measurement of inductance

Maxwell Wien bridge for measurement of inductance and Wien bridge for measurement of capacitance

⇒ The function Z(

*s*) has a pole at infinity if

the degree of numerator and denominator of Z(

*s*) are equal

the numerator of Z(

*s*) is one degree higher than denominator

the denominator of Z(

*s*) is one degree higher than numerator

the degree of numerator and denominator are either equal or differ by one

⇒ In case of low level amplitude modulation system, the amplifiers following the modulated stage must be

class C amplifiers

linear devices

non-linear devices

harmonic devices

⇒ State variables which describe a system are a unique set.

TRUE

FALSE

⇒ In N channel MOSFET with gate reverse biased, the gate current is of the order

10

^{-3}amp

10

^{-6}amp

10

^{-9}amp

10

^{-12}amp