Question is ⇒ Performance of a PIN diode switch is represented by, Options are ⇒ (A) insertion loss when switch is off, (B) insertion loss when switch is on, (C) insertion loss when switch is on and isolation loss when switch is off, (D) insertion loss when switch is off and isolation loss when switch is on, (E) , Leave your comments or Download question paper.

Question is ⇒ Performance of a PIN diode switch is represented by, Options are ⇒ (A) insertion loss when switch is off, (B) insertion loss when switch is on, (C) insertion loss when switch is on and isolation loss when switch is off, (D) insertion loss when switch is off and isolation loss when switch is on, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Performance of a PIN diode switch is represented by
A.	insertion loss when switch is off [Wrong Answer]
B.	insertion loss when switch is on [Wrong Answer]
C.	insertion loss when switch is on and isolation loss when switch is off [Correct Answer]
D.	insertion loss when switch is off and isolation loss when switch is on [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In 8085
the upper 8 address bits appear on address bus and lower 8 bits on address data bus
the lower 8 address bits appear on address bus and the upper 8 address bits appear on address data bus
either upper or lower 8 address bits may appear at address bus
either upper or lower 8 address bits may appear at address data bus

⇒ An 8 level encoding scheme is used in a PCM system of 10 kHz channel BW. The channel capacity is
80 kbps
60 kbps
30 kbps
18 kbps

⇒ The main advantage of superheterodyne receiver is
better tracking
simple cut
better alignment
improvement in selectivity and sensitivity

⇒ The temperature coefficient of copper is 0.00393 at 20° C. At 50° C the temperature coefficient is
0.0042
0.0035
0.0025
0.0015

⇒ A hot wire instrument is not affected by stray magnetic fields.
TRUE
FALSE

⇒ In pulse width modulation of chopper
T is kept constant and T_on is varied
T_on is kept constant T is varied
both T and T_on are varied
either T or T_on is varied

⇒ The input impedance of CRO is about
zero
10 Ω
100 Ω
one mega ohm

⇒ The use of microprocessor control in automobiles results in
improved fuel economy
improved car control
advanced information system for driver
all of the above

⇒ Flash ADC is
serial ADC
parallel ADC
series-parallel ADC
successive approximation ADC

⇒ A XOR gate has inputs A and B and output Y. Then the output equation is
Y = AB
Y = AB + A B
Y = A B + A B
Y = A B + A B

⇒ Alternating current can induce voltage because it has magnetic field which is
constant
time varying
stronger field than D.C.
closed loop nature.

⇒ In the stabilized reactance modulators AFC system
the discriminator must have a fast time constant to prevent demodulation
the higher discriminator frequency the better the oscillator frequency stability
the discriminator frequency must not be too low, or the system will fail
phase modulation is converted into FM by the equalizer circuit

⇒ Modulated carrier power in FM
increases with modulating signal power
decreases with modulating signal power
is independent of the modulating signal power
none

⇒ An amplifier operating over a frequency range of 18 to 20 MHz has 10 kΩ input resistance. At a temperature of 27° C, the noise voltage at input of amplifier is (Boltzman constant k = 1.38 x 10^-23 J/K)
18.2 μV
182 μV
16.2 μV
162 μV

⇒ Consider the real expression in Pascal language XZ and MP + K
XZ + Y and MP + K
(MP + K + X) / Y
Y / (MP + K)

⇒ The heat sink disposes off heat mainly by
radiation
natural convection
forced convection
conduction

⇒ In a bipolar transistor the barrier potential
0
a total of 0.7 V
0.7 V across each depletion layer
0.35 V

⇒ Which TM mode in rectangular waveguide has lowest cutoff frequency?
TM₁₁
TM₀₁
TM₁₀
TM₂₁

⇒ A single element strain gauge bridge has two fixed resistances R₁ and R₁ of 120 Ω each and a variable resistance which gives full deflection at 120 Ω for zero strain and 120.6 Ω for straine e. If gauge factor is 2, strain e is
0.0025
0.0035
0.005
0.0075

⇒ In order to enable TRAP interrupt, which of the following instructions are needed?
El only
SIM only
El and SIM both
None

⇒ Which of the following is the disadvantage of PDM and PPM?
It requires pulses of larger widths
More samples are needed per second
More powerful transmitter is required
None of the above

⇒ Which is not a valid dimension statement?
DIMENSION KAT(10, 20)
DIMENSION BAT (30, 20)
DIMENSION KAT(K, 10)
DIMENSION BAT (10, 5)

⇒ In the equivalent circuit of a moving coil cone type loudspeaker, the mass of the moving system is represented by
a resistance
a capacitance
an inductance
a conductance

⇒ The term VLSI generally refers to a digital IC having
more than 1000 gates
more than 100 gates
more than 1000 but less than 9999 gates
more than 100 but less than 999 gates

⇒ For the logic circuit given, what is the simplified Boolean funct
X = AB + C
X = BC + A
X = AB + AC
X = AC + B

⇒ In satellite communication, highly directional antennas are used to
direct the spot beam to a particular region of space on Earth
strengthen the beam to overcome the cosmic noise
make corrections in change of polarisation of the beam
select a particular channel in transmission and reception

⇒

Assertion (A): Secondary instruments require calibration at frequent intervals.

Reason (R): Secondary instruments have many errors.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ Modulation is also called detection.
TRUE
FALSE

⇒ Which of the following statements is not correct for thermistors?
They have negative temperature coefficient of resistance
The sensing element is made of sintered ceramics, which are oxides of metals in the form of beads
The variation of resistance with temperature is linear
The resistance value at ambient temperature may range from 100 Ω to 100 kΩ

⇒ In microwave communication links, when fading due to rain attenuation occurs then technique adopted for solving the problem would include
antenna replacement and feed correction
amplitude timing and phase correction
polarization shifting and code diversity
path diversity and frequency diversity