Question is ⇒ Perforated cover plates are particularly suitable for built up sections consisting of., Options are ⇒ (A) channels placed back to back, (B) channels placed toe to toe, (C) four angle box section, (D) all the above., (E) , Leave your comments or Download question paper.

Question is ⇒ Perforated cover plates are particularly suitable for built up sections consisting of., Options are ⇒ (A) channels placed back to back, (B) channels placed toe to toe, (C) four angle box section, (D) all the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Perforated cover plates are particularly suitable for built up sections consisting of.
A.	channels placed back to back [Wrong Answer]
B.	channels placed toe to toe [Wrong Answer]
C.	four angle box section [Correct Answer]
D.	all the above. [Wrong Answer]
View Answer 37 -7 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Live load.
varies in magnitude
varies in position
is expressed as uniformly distributed load
All the above.

⇒ Rocker bearings are suitable for span
Less than 8 m
Upto 12 m
12 to 20 m
More than 20 m

⇒ When two plates are placed end to end and are joined by two cover plates, the joint is known as.
lap joint
butt joint
chain riveted lap joint
double cover butt joint.v

⇒ The effective length of a double angle strut with angles placed back to back and connected to both the sides of a gusset plate, by not less than two rivets, is.
0.5 L
0.67 L
0.85 L
L

⇒ The mechanism method and the statical method give
lower and upper bounds respectively on the strength of structure
upper and lower bounds respectively on the strength of structure
lower bound on the strength of structure
upper bound on the strength of structure

⇒

Poisson's ratio for steel within elastic limit, ranges from.

0.15 to 0.20
0.25 to 0.24
0.25 to 0.33
0.33 to 0.35

⇒ The most commonly used sections in lateral system to carry shear force in built up columns, are.
rolled steel flats
rolled angles
rolled channels
all the above.

⇒ Which operation can not be done easily on mild steel ?
Drilling
Punching
Cutting
Hardening

⇒ Which one of the following methods of design is not suitable for structures subjected to impact and fatigue ?
Simple design
Semi-rigid design
Rigid design
Plastic-design

⇒ A 20 mm dia steel bar which is subjected to an axial tension of 2300 kg/cm² produces a strain of 0.004 cm. If Young's modulus of steel is 2.1 x 10⁶ kg/cm², the bar is.
in the elastic range
in the plastic range
at yield point
none of these.

⇒ The centrifugal force due to curvature of track is assumed to act on the bridge at a height of
1.23 m above the rail level
1.50 m above the rail level
1.83 m above the rail level
2.13m above the rail level

⇒ The maximum tensile and compressive bending stress in extreme fibres of rolled I-sections and channels on the effective section, is.
1500 kg/cm2
1420 kg/cm2
1650 kg/cm2
2285 kg/cm2

⇒ Rolled steel angle sections are classified
Equal angles
Unequal angles
Bulb angles
All the above

⇒ The maximum permissible slenderness ratio of compression member carrying dead and superimposed load, is.
180
200
250
300

⇒ For structural steel works the diameter of hot driven rivets is
16 mm
18 mm
20 min to 22 mm
All the above

⇒ Size of rivet is specified by
Shape
Diameter of head
Shank diameter
Weight

⇒ Gantry girders are designed to resist
lateral loads
longitudinal loads and vertical loads
lateral, longitudinal and vertical loads
lateral and longitudinal loads

⇒ The main beam is a beam which supports
Floor construction
Joists
Secondary beam
Both (B) and (C)

⇒ An imaginary line along which rivets are placed, is known as.
rivet line
scrieve line
gauge line
all the above.

⇒ The capacity of the smallest pressed steel tank is
1000 litre
1650 litre
1950 litre
2450 litre

⇒ The maximum value of slenderness ratio of compression members carrying loads resulting from dead loads and superimposed load is
100
180
150
200

⇒

Pick up the correct statement from the following:

Tacking rivets are used if the minimum distance between centres of two adjacent rivets exceeds 12 t or 200 mm, whichever is less
Tacking rivets are not considered to calculate stress
Tacking rivets are provided throughout the length of a compression member composed of two components back to back
All the above.

⇒ A channel section consist of
Two webs
Two flanges
Two webs and two flanges
One web and two flanges

⇒ If N is the number of rivets in the joint, the strength of a riveted joint against shearing of rivets, is given by.
Ps = N x (Ï€/4) d2 x Ps
Ps = N x (d x t x ps)
Ps = N x (p - d) x t x Ps
Ps = N x (P + d) x t x ps.

⇒ When a tension member is made of four angles with a plate as a web, the allowance for holes is made as.
two holes for each angle and one hole for the web
one hole for each angle and one hole for the web
one hole for each angle and two holes for the web
two holes for each angle and two holes for the web

⇒ If the area of cross-section of a single angle discontinuous strut is 30 cm² and allowable working stress corresponding to its slenderness ratio is 625 kg/cm², the safe load carrying capacity of the member, is.
10 tonnes
12 tonnes
15 tonnes
18 tonnes

⇒

A column splice is used to increase.

length of the column
strength of the column
cross-sectional area of the column
none of these.

⇒

For simply supported beams, the maximum permitted deflection, is.

1/325 of the span
1/350 of the span
1/375 of the span
1/375 of the span

⇒ Fillet weld is not used for joining the parts, when the angle between fusion faces is
Greater than 120°
Less than 60°
Both are correct
Both are wrong

⇒ The slenderness ratio of a column is zero when its length.
is zero
is equal to its radius of gyration
is supported on all sides throughout its length
is between the points of zero moments.