Question is ⇒ Assertion (A): A semiconductor strain gauge is more accurate than a resistance strain gauge.Reason (R): The gauge factor of a semiconductor strain gauge is about 100 where as the gauge factor of a resistance strain gauge is only about 2. , Options are ⇒ (A) Both A and R are true and R is correct explanation of A, (B) Both A and R are true but R is not correct explanation of A, (C) A is true R is false, (D) A is false R is true, (E) , Leave your comments or Download question paper.

Question is ⇒ Assertion (A): A semiconductor strain gauge is more accurate than a resistance strain gauge.Reason (R): The gauge factor of a semiconductor strain gauge is about 100 where as the gauge factor of a resistance strain gauge is only about 2. , Options are ⇒ (A) Both A and R are true and R is correct explanation of A, (B) Both A and R are true but R is not correct explanation of A, (C) A is true R is false, (D) A is false R is true, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Assertion (A): A semiconductor strain gauge is more accurate than a resistance strain gauge. Reason (R): The gauge factor of a semiconductor strain gauge is about 100 where as the gauge factor of a resistance strain gauge is only about 2.
A.	Both A and R are true and R is correct explanation of A [Correct Answer]
B.	Both A and R are true but R is not correct explanation of A [Wrong Answer]
C.	A is true R is false [Wrong Answer]
D.	A is false R is true [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The symbol in figure is
SUS
SBS
SCS
Shockley diode

⇒ To convert JK flip flop to D flip flop
connect D to both J and K
connect D to J directly and D to K through inverter
connect D to K directly and D to J through inverter
connect D to K and leave J open

⇒ In a rectangular waveguide cutoff wavelength for TE₁₀mode is 8 cm. Then cutoff wavelength for TE₂₀ mode is
8 cm
6 cm
4 cm
2 cm

⇒ A 10 km long line has a characteristic impedance of 400 ohms. If line length is 100 km, the characteristic impedance is
4000 Ω
400 Ω
40 Ω
4 Ω

⇒ A vertical wire of 1 meter length carries a current of 1 A at 10 MHz. The total radiated power is nearly
0.13 W
0.88 W
7.3 W
73 W

⇒ In a turnstile antenna two-half wave resonant wire radiators are placed at 90° to each other in the same plane and are excited
in phase
in phase opposition
90° out of phase with each other
45° out of phase with each other

⇒ In an unloaded transformer, the fluxes limiting the primary and secondary are 30 mWb and 20 mWb. The coefficient of coupling is
1
0.1
0.33
0.67

⇒

Match the following:

	List I (Memories)		List II (Characteristic)
A.	Static PLA	1.	erasable, programmable
B.	CCD	2.	ultra high speed
C.	ECL	3.	stores large volume of data
D.	GAL	4.	Does not need refreshing
		5.	Non-volatile

A-4, B-3, C-2, D-1
A-4, B-2, C-3, D-1
A-5, B-1, C-2, D-3
A-3, B-5, C-2, D-1

⇒ In figure, the time constant for the capacitor chargin
6 μs
10 μs
15 μs
25 μs

⇒ As a compared to a CB amplifier, a CE amplifier has
lower current amplification
higher current amplification
lower input resistance
higher input resistance

⇒ In figure the cut in voltage of diode is 0.7 V and its bulk resistance is 20 Ω. The peak value of circuit current of during positive and negative half cycles
10 mA and zero
9.12 mA and zero
9.3 mA and zero
zero and 9.12 mA

⇒ In 8085 microprocessor, when TRAP interrupt is triggered program control is transferred to location
0020 H
0024 H
0028 H
002 CH

⇒ In a specimen of ferromagnetic material, as the flux density is increased from zero to 2.5 T, µ_r will
increase
decrease
first decrease then increase
first increase then decrease

⇒ The correct relation between energy and charge is
Energy = voltage/charge
Charge = Energy x voltage
Energy = voltage (charge)^0.5
Energy = voltage x charge

⇒ The minimum decimal equivalent of the number 11C0 is
183
194
268
269

⇒ An op-amp integrating circuit uses
an inductor
a capacitor
both inductor and capacitor
none of the above

⇒ The logic circuit given below converts a binary code y₁ y₂, y₃
Excess - 3 code
Gray code
BCD code
Hamming

⇒ Which of the- following display consumes least amount of power?
LCD
LED
Fluorescent display
All display consume same power

⇒ For free space propagation
γ = a + jβ
γ = jβ
γ = a
a = β = 0

⇒ The owner of a communication satellite is usually required to keep the spacecraft on station at its assigned place in the geosynchronous orbit with an accuracy of __________ degree.
0.1
1
2
0.5

⇒ If CS = A₁₅ A₁₄ A₁₃ is used as chip select logic of a 4 K RAM in 8085 system, its memory range is
3000 H - 3 FFF H
7000 H - 7 FFFH
5000 H - 5 FFF H and 6000 H - 6 FFF H
6000 H - 6 FFF H and 7000 H - 7 FFF H

⇒ In a 4 input AND gate, the total number of High outputs for 16 input states are
16
8
4
1

⇒ The resistance of a dc galvanometer is 20 Ω. A current of 10 mA causes full scale deflection. To convert it into 0-300 V voltmeter, we have to use a series resistance of
30000 Ω
29980 Ω
6000 Ω
15 Ω

⇒ In a single phase full wave regulator feeding a resistive load, the average current over one full cycle
is always zero
cannot be zero
may be sometimes zero
is always positive

⇒ Binary 1000 will be the result of which of the following?
Binary 1000 - 100
Binary 1011 - 1111
Binary 1111 - 111
Binary 11111 - 1111

⇒ The duty cycle of a radar transmitter is equal to
(PRF) (pulse width)
(PRF)/(pulse width)
(pulse width)/(PRF)
(pulse width) + (PRF)

⇒ Consider the following statemen
1, 2, 3, 4
1, 2, 3
1, 2
1, 3, 4

⇒ Find resistance R_B to bring transistor to threshold of saturation V_CB = 0, V_BE = 0.7 V, a =
1.5 kΩ
15 kΩ
10 kΩ
1 kΩ

⇒ It is desired to clean up ragged looking pulsed that have been distorted during transmission from one place to another, which of the following device will be appropriate?
Multiplexer
D/A converter
JK flip-flop
Schmitt trigger

⇒ The trigonometric Fourier series for the waveform f(t) shown below con
only cosine terms and zero value for the dc component
only cosine terms and a positive value for the dc component
only cosine terms and a negative value for the dc component
only sine terms and a negative for the dc component