Question is ⇒ optical reading instruments., Options are ⇒ (A) the vertical circle is usually continuous from 0Â° to 359Â°, (B) the readings increase when the telescope is elevated in the face left position, (C) the readings decrease when the telescope is elevated in the face right position, (D) all the above., (E) , Leave your comments or Download question paper.

Question is ⇒ optical reading instruments., Options are ⇒ (A) the vertical circle is usually continuous from 0Â° to 359Â°, (B) the readings increase when the telescope is elevated in the face left position, (C) the readings decrease when the telescope is elevated in the face right position, (D) all the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	optical reading instruments.
A.	the vertical circle is usually continuous from 0Â° to 359Â° [Wrong Answer]
B.	the readings increase when the telescope is elevated in the face left position [Wrong Answer]
C.	the readings decrease when the telescope is elevated in the face right position [Wrong Answer]
D.	all the above. [Correct Answer]
View Answer 13 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For preparation of a contour plan for a route survey.
method of squares is used
method of trace contour is used
method of cross profile is used
indirect method of contouring is used.

⇒ In horizontal angles, the error due to imperfect levelling of the plate bubble is.
large when sights are nearly level
large for long sights
less for steeply inclined sights
large for steeply inclined sights.

⇒ The instrument used for accurate centering in plane table survey is
spirit level
alidade
plumbing fork
trough compass

⇒ In the quadrantal bearing system, a whole circle bearing of 293° 30' can be expressed as
W23°30'N
N66°30'W
S113°30'N
N23°30'W

⇒ Volume of the earth work may be calculated by.
mean areas
end areas
Prismoidal formula
all the above.

⇒ A clinometer is used for.
measuring angle of slope
correcting line of collimation
setting out right angles
defining natural features.

⇒ While viewing through a level telescope and moving the eye slightly, a relative movement occurs between the image of the levelling staff and the cross hairs. The instrument is.
correctly focussed
not correctly focussed
not correctly focussed
free from parallax.

⇒ In a precision traverse, included angles are measured by setting the vernier.
to read zero exactly on back station
to read 5Â° exactly on back station
some where near zero and reading both verniers on back station
all the above.

⇒ If R is the radius of the main curve, θ the angle of deflection, S the shift and L the length of the transition curve, then, total tangent length of the curve, is.
(R - S) tan Î¸/2 - L/2
(R + S) tan Î¸/2 - L/2
(R + S) tan Î¸/2 + L/2
(R - S) tan Î¸/2 + L/2

⇒ In direct method of contouring, the process of locating or identifying points lying on a contour is called
ranging
centring
horizontal control
vertical control

⇒ At the equator, the amount of dip is
0°
45°
60°
90°

⇒ Which of the following methods of plane table surveying is used to locate the position of an inaccessible point ?
radiation
intersection
traversing
resection

⇒ Determining the difference in elevation between two points on the surface of the earth, is known as.
levelling
simple levelling
differential levelling
longitudinal levelling.

⇒ If the smallest division of a vernier is longer than the smallest division of its primary scale, the vernier is known as
Direct vernier
Double vernier
Simple vernier
Retrograde vernier

⇒ With usual notations, the expression V²/gR represents
centrifugal force
centrifugal ratio
super elevation
radial acceleration.

⇒ In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is.
5.24 cm
6.24 cm
7.24 cm
8.24 cm

⇒ In levelling operation.
when the instrument is being shifted, the staff must not be moved
when the staff is being carried forward, the instrument must remain stationary
both (a) and (b)
neither (a) nor (b).

⇒ The line of collimation method of reduction of levels, does not provide a check on.
intermediate sights
fore sights
back sights
reduced levels.

⇒ The magnetic meridian at a point can be fixed by
Bar magnets
Electro-magnets
Magnetic compass
None of the above

⇒ As per Indian Standard the total number of links in a 30 metre chain should be
100
150
300
75

⇒ Metric chains are generally available in.
10 m and 20 m length
15 m and 20 m length
20 m and 30 m length
25 m and 100 m length

⇒ Pick up the correct statement from the following:
the theodolite in which telescope can be rotated in vertical plane is called a transmit
when the vertical circle is to the left of the telescope during observation, it is called to be in left face
when the vertical circle is to the right of the telescope during observation, it is called to be in right face
all the above.

⇒ For true difference in elevations between two points A and B, the level must be set up.
at any point between A and B
at the exact mid point of A and B
near the point A
near the point B.

⇒ Pick up the correct statement from the following :
with both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from knots
the follower of the chaining operation should be more experienced than the leader
at the end of the tenth chain length, the two chain men meet and the ten arrows are handed over to the leader
all the above.

⇒ The sum of the interior angles of a geometrical figure laid on the surface of the earth differs from that of the corresponding plane figure only to the extent of one second for every.
100 sq. km of area
150 sq. km of area
200 sq. km of area
none of these.

⇒ The slope correction may be ignored if.
the slope of the ground is less than 3Â°
to slope of the ground is say 1 in 19
both (a) and (b)
neither (a) nor (b)

⇒ If the length of a transition curve to be introduced between a straight and a circular curve of radius 500 m is 90 m, the maximum deflection angle to locate its junction point, is.
1Â°43' 08"
1Â°43' 18"
1Â°43' 28"
1Â°43' 38"

⇒ Overturning of vehicles on a curve can be avoided by using
compound curve
vertical curve
reverse curve
transition curve

⇒ The main principle of surveying is to work.
from part to the whole
from whole to the part
from higher level to the lower level
from lower level to higher level.

⇒ The first temporary adjustment of a prismatic compass is
Levelling
Focussing of the prism
Removing the parallax
Centring