Question is ⇒ One volt equals, Options are ⇒ (A) one joule, (B) one joule/coulomb, (C) one coulomb/joule, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ One volt equals, Options are ⇒ (A) one joule, (B) one joule/coulomb, (C) one coulomb/joule, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	One volt equals
A.	one joule [Wrong Answer]
B.	one joule/coulomb [Wrong Answer]
C.	one coulomb/joule [Correct Answer]
D.	none of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The circuit of figure is generally employed
bridge
low-pass filter
peaking network
high-pass filter

⇒ What was the first commercial geostationary communication satellite?
INTELSAT 1
ECHO
INSAT-1A
SPUTNIK

⇒ ARQ stands for
Automatic Repeat Quest
Analog Repeat Request
Automatic Repeat Request
None Of the above

⇒ A signal x(t) = 100 cos (24p x 10³t) is ideally sampled with a sampling period of 50 μ sec and then passed through an ideal low pass filter with cut off frequency of 15 kHz Which of the following frequencies are present at the filter output?
12 kHz only
8 kHz only
12 kHz and 9 kHz
12 kHz and 8 kHz

⇒ The circuit in figur
CE amplifier
CB amplifier
Constant voltage source
Constant current source

⇒ In Bode plots the frequency at which two asymptotes meet is called corner frequency.
TRUE
FALSE

⇒ A ring counter with 5 flip-flops will have __________ states.
5
10
32
Infinite

⇒ A three-section RC phase shift oscillator has R = 10K ohms and C = 0.001 μF. The frequency of oscillations is
1.1 kHz
2.5 kHz
3.3 kHz
6.5 kHz

⇒ The impurity added to extrinsic semiconductor is of the order of
1 in 100
1 in 1000
1 in 100, 0000
1 in 100, 000, 000

⇒ When a power diode is conducting, the voltage drop across it is about
I V
5 V
20 V
50 V

⇒ In a resistance strain gauge, G = 2, stress = 1050 kg/cm², R = 1000 Ω. The value of ΔR will be
2 Ω
3 Ω
4 Ω
1 Ω

⇒ A dynamometer wattmeter can be used for
dc only
ac only
dc and 50 Hz ac
dc and high frequency ac

⇒ In an AM system, doubling of modulation index doubles the antenna current. The system is
single side band full carrier
vestigial side band
single side band suppressed carrier
double side band full carrier

⇒

Assertion (A): Superposition theorem can be used to find the output of a full wave rectifier excited by sinusoidal signal sources of different frequencies connected in series.

Reason (R): Superposition theorem is valid for all linear systems.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ The language PL / I has
one character set having 60 characters
one character set having 48 characters
one character set having 60 characters and another character set having 48 character
none of the above

⇒ Which of the following is a microwave source with a 'cross-field' structure?
Double cavity klystron
Reflex klystron
Magnetron
Travelling wave tube

⇒ When a ferromagnetic substance is magnetised, there are small changes in its dimensions. This phenomenon is called
hysteresis
magnetostriction
diamagnetism
bipolar relaxation

⇒ In a 3 phase fully controlled converter the firing frequency is
3 times the line frequency
6 times the line frequency
9 times the line frequency
12 times the line frequency

⇒ Which circuit is called emitter follower?
CC
CE
CB
Both (a) and (b)

⇒ The control logic for a binary multiplier is specified by a states diagram. The state diagram has four states and two inputs. To implement it by the sequence register and decoder method.
two flip-flop & 2 x 4 decoder are needed
four flip-flop & 2 x 4 decoder are needed
two flip-flop & 3 x 9 decoder are needed
four flip-flop & 3 x 9 decoder are needed

⇒ Transfer function of a linear system is 200 e^-j10ω The system is a
distortionless Attenuator
amplifier with Phase distortion
distortionless Amplifier
attenuator with Phase distortion

⇒ Which of the following statements regarding two transistor model of p-n-n-p device is correct?
It explain only the turn on portion of the device characteristics
It explain only the turn off portion of the device characteristics
It explain only the negative region portion of the device characteristics
It explain all the regions of the device characteristics

⇒ A periodic voltage v(t) = 1 + 4 sin ωt + 2 cos ωt is applied across a 1 ohm resistance. The power dissipated is
1 W
11 W
21 W
24.5 W

⇒ Symbol shown in figure represen
P-channel enhancement MOSFET
N-channel DEMOSFET
UJT with P-type base
UJT with N-type base

⇒ The number of registers and flags in 8086 are
13 and 5 respectively
9 and 5 respectively
13 and 9 respectively
9 and 9 respectively

⇒ For a periodic signal with finite number of discontinuities in each period, at isolated points of discontinuity the series converges to __________ .
difference value of signal on either side of discontinuity
highest value of signal on either side of discontinuity
average value of signal on either side of discontinuity
sum of value of signal on either side of discontinuity

⇒ The efficiency of a chopper circuit is about
80% or more
around 50%
around 20%
around 5%

⇒ A system has its two poles on the negative real axis and one pair of poles lies on jω axis. The system is
stable
unstable
limitedly stable
either (a) or (c)

⇒ The subtraction of a binary number Y from another binary number X, done by adding the 2's complement of Y to X results in a binary number without overflow. This implies that the result is
-ve and is in normal form
-ve and 2's complement form
+ve and is in normal form
+ve and in 2's complement

⇒ Which of the following statements is non-executable in FORTRAN 77?
DO
ASSIGN
END
DIMENSION