Question is ⇒ One electron volt is equivalent to, Options are ⇒ (A) 1.6 x 10-10 joule, (B) 1.6 x 10-13 joule, (C) 1.6 x 10-16 joule, (D) 1.6 x 10-19 joule, (E) , Leave your comments or Download question paper.

Question is ⇒ One electron volt is equivalent to, Options are ⇒ (A) 1.6 x 10-10 joule, (B) 1.6 x 10-13 joule, (C) 1.6 x 10-16 joule, (D) 1.6 x 10-19 joule, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	One electron volt is equivalent to
A.	1.6 x 10^-10 joule [Wrong Answer]
B.	1.6 x 10^-13 joule [Wrong Answer]
C.	1.6 x 10^-16 joule [Wrong Answer]
D.	1.6 x 10^-19 joule [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a series R-L-C circuit, the voltage across inductance will be maximum
at resonance frequency
just before resonant frequency
just after resonant frequency
none of the above

⇒ A pole zero pattern of a certain filter is shown in figure. This filter mus
LPF
BFP
HPF
APF

⇒ The skip distance is
same for each layer
independent of frequency
independent of the state of ionisation
independent of transmitted power

⇒ The noise figure of individual stages of a two stage amplifier is 2.03 and 1.54 respectively. If gain of first stage is 62, the overall noise figure is
2.03
2.055
3.05
6.05

⇒ Crossover distortion behaviour is characteristic of
class A O/P stage
class B O/P stage
class AB output stage
common pulse O/P state

⇒

Assertion (A): In reverse biased p-n junction, the reverse saturation current is nearly constant if the reverse voltage is less than critical value.

Reason (R): The total reverse current is sum of reverse saturation current and surface leakage current.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Using the same flip flops
a synchronous flip flop can operate at higher frequency than ripple counter
a ripple counter can operate at higher frequency than synchronous counter
both ripple and synchronous counter can operate at the same frequency
can not determine

⇒ A single phase half wave converter is feeding a resistive load. Just before triggering, the voltage across thyristor is
zero
about 1 V
same as input voltage
twice the input voltage

⇒ Consider the following statements:

A flip-flop is used to store 1-bit of information.
Race-around condition occurs in a J-K flip-flop when both the inputs are 1.
Master-slave configuration is used in flip-flops to store 2-bits of information
A transparent latch consists of a D-type flip-flop.

Which of the above statements is/are correct?
1 only
1, 3 and 4
1, 2 and 4
2 and 3 only

⇒ The effective height of an antenna is slightly greater than physical height because
wave velocity in conductor is less than its velocity in free space
wave velocity in conductor is more than its velocity in free space
resistance of conductor is less than that of free space
none of the above

⇒ The language PL / I has
one character set having 60 characters
one character set having 48 characters
one character set having 60 characters and another character set having 48 character
none of the above

⇒ Windows can run several tasks simultaneously.
TRUE
FALSE

⇒ The temperature coefficient of a thermistor
is positive
is negative
zero
may be positive or negative depending on its composition

⇒ In a pneumatic bellows
the input surface, output surface and side walls are corrugated
the input surface and output surface are flat but the side walls are corrugated
the input surface and side walls are flat but the output surface is corrugated
the input surface and output surface are corrugated but the side walls are flat

⇒ Which component is allowed to pass through it by a choke filter?
Dc
Ac
Both dc and ac
Only high frequency ac

⇒ The pole-zero configuration of the given figure can be
lag compensator
lead compensator
lead-lag compensator
series compensator

⇒ In a microprocessor the clock signal
is always generated internally
is always supplied externally
may be generated internally or supplied externally
is mostly supplied externally

⇒ In a conductor which of the following relations hold good?
∇ x D = r
∇ . D = r
∇ x D = 0
∇ . D = 0

⇒ Which one is correct?
Sky wave propagation (2 to 30 MHz)
Space wave propagation (> 30 MHz)
Tropospheric propagation (> 300 MHz)
All of the above

⇒ The frequency range of 300 kHz to 3000 kHz is known as
low frequency
medium frequency
high frequency
very high frequency

⇒ The peak factor is
rms value/peak value
rms value/average value
peak value/rms value
peak to peak value/rms value

⇒ In a line with finite attenuation
power transmission is least efficient when there are no standing waves on the line
power transmission is most efficient when there are no standing waves on line
Load power depends on phase constant
standing waves will always exist on the line

⇒ The real part of complex frequency s corresponds to oscillations.
TRUE
FALSE

⇒ The value of parameter r_e used in r_e transistor model
increases with increase in temperature
decreases with increase in temperature
is not affected by increase in temperature
either (b) or (c)

⇒ At a P-N junction, the potential barrier is due to the charges on either side of the junction, which consists of
fixed donor and acceptor ions
majority carriers only
minority carriers only
both majority and minority carriers

⇒ With a JK master-slave flip-flop the master is clocked when the clock is __________ , and the slave is triggered when the clock is __________ .
low, low
high, low
low, high
high, high

⇒ The no. of comparators required in a 3 bit comparator type ADC is
2
3
7
8

⇒ A notch filter is sometimes used in communication receivers to
reduce receiver gain at some specific frequency
increase receiver gain at some specific frequency
made selectivity more precise
spread the bandwidth

⇒ A device has two resistances 300 Ω and 200 Ω respectively. The noise voltages due to these two resistance calculated separately are 5.38 μV and 4.38 μV respectively. When both of them are used together, the noise voltage will be
9.76 V
1 μV
23.56 μV
6.94 μV

⇒ In a Hurwitz polynomial
all coefficients are non-negative
the coefficients may be positive or negative
all coefficients are negative
all coefficients are non-negative and all zeros should be either in left half plane or simple on the imaginary axis