Question is ⇒ Often earing defects are found during deep drawing operation, because the, Options are ⇒ (A) surface finish of the sheet is poor., (B) sheet material has been given substantial spring back., (C) starting sheet has planer anisotropy due to its texture., (D) starting sheet has normal anitropy due to its texture., (E) , Leave your comments or Download question paper.

Question is ⇒ Often earing defects are found during deep drawing operation, because the, Options are ⇒ (A) surface finish of the sheet is poor., (B) sheet material has been given substantial spring back., (C) starting sheet has planer anisotropy due to its texture., (D) starting sheet has normal anitropy due to its texture., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Often earing defects are found during deep drawing operation, because the
A.	surface finish of the sheet is poor. [Wrong Answer]
B.	sheet material has been given substantial spring back. [Wrong Answer]
C.	starting sheet has planer anisotropy due to its texture. [Correct Answer]
D.	starting sheet has normal anitropy due to its texture. [Wrong Answer]
View Answer 12 -7 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ All of the following alloying elements of steel increases hardness but sacrifice ductility, except
nickel
vanadium
molybdenum
chromium

⇒ In case of simple harmonic motion, displacement is proportional to the
velocity
acceleration
both (a) & (b)
neither (a) nor (b)

⇒ Heat transfer by radiation from a hot body will be most rapid, if its surface is __________ because of its higher emissivity.
white & rough
black & rough
white & polished
black & polished

⇒ The burnout heat flux in the nucleate boiling regime is not a function of the
liquid density.
vapour density.
temperature difference.
heat of evaporation.

⇒ The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm.
0.001
0.01
0.002
0.02

⇒ Thermal conductivity of a material does not depend upon its
mass
volume
surface area
all 'a', 'b' & 'c'

⇒ The 'laughing gas' is
nitrous oxide
nitric oxide
nitrogen trioxide
nitrogen pentoxide

⇒ In the floatation process, pine oil is used as the
collector
activator
frother
depressant

⇒ Out of the following, the __________ pipe has the least corrosion resistance.
mild steel
copper
cast iron
wrought iron

⇒ A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C.
370
340
320
300

⇒ Water-tube boiler is the one, in which
water passes through tubes and flue gases around it.
tube carrying hot flue gases are immersed in a pool of water.
tubes are placed in vertical position.
none of these.

⇒ Which of the following materials has the poorest electrical conductivity ?
Carbon
Aluminium
Silver
Stainless steel

⇒ Ester is formed, when an alcohol reacts with
carboxylic acid
aldehyde
ketone
ether

⇒ The term 'Value' in value engineering technique refers to the __________ cost of the product.
function (utility)
selling
production
total

⇒ Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.
bomb
throttling
Junker's
Boy's

⇒ Cold cracking in the heat affected zone of a high strength steel weld can take place because of the
retained austenite.
martensite formation.
relatively high sulphur content in the base metal.
sufficient hydrogen present in the welding arc.

⇒ Ingrannular corrosion occurs __________ stainless steel.
in all types of steels except
at the surface of
along grain boundaries of
in the core of

⇒ Superheating of steam is done at constant
enthalpy
entropy
pressure
volume

⇒ Which of the following forces does not act on a fluid at rest ?
Viscous force
Gravity force
Hydrostatic force
Surface tension force

⇒ Air refrigeration cycle is used in the air crafts, because of
low temperature encountered at high altitude.
its high heat transfer rate.
its low unit weight per ton of refrigeration.
its higher co-efficient of performance (COP).

⇒ While the oxy-acetylene flame produces a temperature of 3200°C, the temperature produced by oxy-hydrogen flame is about __________ °C.
1800
2000
2400
3000

⇒ Pick out the correct combination about the role of various additives used in polymers.
Plasticiser : increases the polymer strength.
Heat stabiliser : increases the maximum service temperature.
Fillers: Does not affect the property of polymer but increases its weight.
Lubricants: increases the flexibility of polymers.

⇒ Which of the following is not a cupro-nick-el alloy ?
German silver
Monel metal
Muntz metal
None of these

⇒ Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of portland cement. The component of Portland cement which first hardens is
5CaO . 3 Al₂O₃
3CaO . Al₂O₃
3CaO . SiO₂
2CaO . SiO₂

⇒ Angular displacement can be measured suitably by a
shaft encoder.
linear variable differential transducer (LVDT).
stroboscope.
tachometer.

⇒ During brazing, if the fluxes are entrapped, it results in the
distortion of brazed joints.
cracking of joints.
presence of gas pockets.
corrosion.

⇒ What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m². °K ? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
2
5
10
20

⇒ Maximum carbon content in cast iron is __________ percent.
3.8
4
4.3
4.6

⇒ For an ideal gas, C_p - C_v is
R
-R
0
(3/2) R

⇒ __________ number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical.
Mach
Reynolds
Froude
Weber